MC908AZ60ACFU Freescale Semiconductor, MC908AZ60ACFU Datasheet - Page 137

• Manufacturer Part Number: MC908AZ60ACFU
• Description: IC MCU FLASH 8.4MHZ 60K 64QFP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908AZ60ACFU

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8.4MHz
• Connectivity: CAN, SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 52
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 15x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

PCTL3–PCTL0 — Unimplemented
10.5.2 PLL Bandwidth Control Register
The PLL bandwidth control register:
AUTO — Automatic Bandwidth Control Bit
LOCK — Lock Indicator Bit
ACQ — Acquisition Mode Bit
Freescale Semiconductor
it may take up to three CGMXCLK and three CGMVCLK cycles to complete the transition from one
source clock to the other. During the transition, CGMOUT is held in stasis. See
Selector
These bits provide no function and always read as logic 1s.
•
•
•
•
This read/write bit selects automatic or manual bandwidth control. When initializing the PLL for manual
operation (AUTO = 0), clear the ACQ bit before turning on the PLL. Reset clears the AUTO bit.
When the AUTO bit is set, LOCK is a read-only bit that becomes set when the VCO clock, CGMVCLK,
is locked (running at the programmed frequency). When the AUTO bit is clear, LOCK reads as logic 0
and has no meaning. Reset clears the LOCK bit.
When the AUTO bit is set, ACQ is a read-only bit that indicates whether the PLL is in acquisition mode
or tracking mode. When the AUTO bit is clear, ACQ is a read/write bit that controls whether the PLL is
in acquisition or tracking mode.
1 = CGMVCLK divided by two drives CGMOUT
0 = CGMXCLK divided by two drives CGMOUT
1 = Automatic bandwidth control
0 = Manual bandwidth control
1 = VCO frequency correct or locked
0 = VCO frequency incorrect or unlocked
Selects automatic or manual (software-controlled) bandwidth control mode
Indicates when the PLL is locked
In automatic bandwidth control mode, indicates when the PLL is in acquisition or tracking mode
In manual operation, forces the PLL into acquisition or tracking mode
Circuit. Reset and the STOP instruction clear the BCS bit.
Address:
PLLON and BCS have built-in protection that prevents the base clock
selector circuit from selecting the VCO clock as the source of the base clock
if the PLL is off. Therefore, PLLON cannot be cleared when BCS is set, and
BCS cannot be set when PLLON is clear. If the PLL is off (PLLON = 0),
selecting CGMVCLK requires two writes to the PLL control register. See
10.3.3 Base Clock Selector
Reset:
Read:
Write:
MC68HC908AZ60A • MC68HC908AS60A • MC68HC908AS60E Data Sheet, Rev. 6
$001D
AUTO
Figure 10-5. PLL Bandwidth Control Register (PBWC)
Bit 7
0
= Unimplemented
LOCK
6
0
ACQ
5
0
Circuit.
NOTE
XLD
4
0
3
0
0
2
0
0
1
0
0
10.3.3 Base Clock
Bit 0
0
0
CGM Registers
137