PIC18F27J13-I/SP Microchip Technology, PIC18F27J13-I/SP Datasheet - Page 355

• Manufacturer Part Number: PIC18F27J13-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J13-I/SP

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Type: FLASH
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Embedded Interface Type: I2C, SPI, USART
• Rohs Compliant: Yes
• Core: PIC
• Processor Series: PIC18F
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 48 MHz
• Data Ram Size: 3.76 KB
• On-chip Adc: Yes
• Number Of Programmable I/os: 2
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Operating Temperature Range: - 40 C to + 85 C
• A/d Bit Size: 12 bit
• A/d Channels Available: 10
• Height: 3.43 mm
• Interface Type: I2C, SPI, USART
• Length: 34.4 mm
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.15 V
• Width: 7.24 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: MA180030 - BOARD DEMO PIC18F47J13 FS USBMA180029 - BOARD DEMO PIC18F47J53 FS USB
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

REGISTER 24-5:
REGISTER 24-6:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value when device is unprogrammed
bit 7
bit 6
bit 5-3
bit 2
bit 1
bit 0
Note 1:
bit 7
Legend:
R = Readable bit
-n = Value when device is unprogrammed
bit 7-4
bit 3
bit 2
bit 1
bit 0
Note 1:
DEBUG
R/P-1
U-0
—
2:
(2)
Can only be changed by a programmer in high-voltage programming mode.
The DEBUG bit is managed automatically by device development tools including debuggers and programmers. For
normal device operations, this bit should be maintained as a ‘1’.
Available on PIC18(L)FX5K22 and PIC18(L)FX6K22 devices.
DEBUG: Background Debugger Enable bit
1 = Background debugger disabled, RB6 and RB7 configured as general purpose I/O pins
0 = Background debugger enabled, RB6 and RB7 are dedicated to In-Circuit Debug
XINST: Extended Instruction Set Enable bit
1 = Instruction set extension and Indexed Addressing mode enabled
0 = Instruction set extension and Indexed Addressing mode disabled (Legacy mode)
Unimplemented: Read as ‘0’
LVP: Single-Supply ICSP Enable bit
1 = Single-Supply ICSP enabled
0 = Single-Supply ICSP disabled
Unimplemented: Read as ‘0’
STVREN: Stack Full/Underflow Reset Enable bit
1 = Stack full/underflow will cause Reset
0 = Stack full/underflow will not cause Reset
Unimplemented: Read as ‘0’
CP3: Code Protection bit
1 = Block 3 not code-protected
0 = Block 3 code-protected
CP2: Code Protection bit
1 = Block 2 not code-protected
0 = Block 2 code-protected
CP1: Code Protection bit
1 = Block 1 not code-protected
0 = Block 1 code-protected
CP0: Code Protection bit
1 = Block 0 not code-protected
0 = Block 0 code-protected
XINST
R/P-0
U-0
—
CONFIG4L: CONFIGURATION REGISTER 4 LOW
CONFIG5L: CONFIGURATION REGISTER 5 LOW
P = Programmable bit
U-0
U-0
—
—
(1)
(1)
U-0
U-0
Preliminary
—
—
(2)
U = Unimplemented bit, read as ‘0’
x = Bit is unknown
U = Unimplemented bit, read as ‘0’
C = Clearable only bit
CP3
R/C-1
U-0
—
PIC18(L)F2X/4XK22
(1)
CP2
R/C-1
LVP
R/P-1
(1)
(1)
R/C-1
CP1
U-0
—
DS41412D-page 355
STVREN
R/P-1
R/C-1
CP0
bit 0
bit 0