MCHC912B32CFUE8 Freescale Semiconductor, MCHC912B32CFUE8 Datasheet - Page 105

• Manufacturer Part Number: MCHC912B32CFUE8
• Description: IC MCU 32K FLASH 8MHZ 80-QFP
• Manufacturer: Freescale Semiconductor
• Series: HC12r

Specifications of MCHC912B32CFUE8

• Core Processor: CPU12
• Core Size: 16-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 63
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 768 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-QFP
• Cpu Family: HC12
• Device Core Size: 16b
• Frequency (max): 8MHz
• Interface Type: SCI/SPI
• Total Internal Ram Size: 1KB
• # I/os (max): 63
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 4.5V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: PQFP
• Package: 80PQFP
• Family Name: HC12
• Maximum Speed: 8 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 63
• Processor Series: HC912B
• Core: HC12
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 8 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68EVB912B32E
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.5 Programming the FLASH EEPROM
Programming the FLASH EEPROM is accomplished by this step-by-step procedure. The V
must be at the proper level prior to executing step 4 the first time.
The flowchart in
Freescale Semiconductor
10. If the location is programmed, repeat the same number of pulses as required to program the
11. Read the address location to verify that it remains programmed.
12. Clear LAT.
13. If there are more locations to program, repeat steps 2 through 10.
14. Turn off V
1. Apply program/erase voltage to the V
2. Clear ERAS and set the LAT bit in the FEECTL register to establish program mode and enable
3. Write data to a valid address. The address and data are latched. If BOOTP is asserted, an attempt
4. Apply programming voltage by setting ENPE.
5. Delay for one programming pulse, t
6. Remove programming voltage by clearing ENPE.
7. Delay while high voltage is turning off, t
8. Read the address location to verify that it has been programmed,
9. If the location is not programmed, repeat steps 4 through 7 until the location is programmed or until
programming address and data latches.
to program an address in the boot block will be ignored.
the specified maximum number of program pulses, n
location. This provides 100 percent program margin.
FP
Figure 8-5
. Reduce voltage on V
demonstrates the recommended programming sequence.
M68HC12B Family Data Sheet, Rev. 9.1
FP
PPULSE
FP
pin to V
VPROG
pin.
.
DD
.
.
PP
, has been reached.
Programming the FLASH EEPROM
FP
pin voltage
105