LPC3230FET296,551 NXP Semiconductors, LPC3230FET296,551 Datasheet - Page 35

• Manufacturer Part Number: LPC3230FET296,551
• Description: IC ARM9 MCU 256K 296-TFBGA
• Manufacturer: NXP Semiconductors
• Series: LPC32x0r

Specifications of LPC3230FET296,551

• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 266MHz
• Connectivity: EBI/EMI, I²C, IrDA, Microwire, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: DMA, I²S, LCD, Motor Control PWM, PWM, WDT
• Number Of I /o: 51
• Program Memory Type: ROMless
• Ram Size: 256K x 8
• Voltage - Supply (vcc/vdd): 0.9 V ~ 3.6 V
• Data Converters: A/D 3x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 296-TFBGA
• Processor Series: LPC32
• Core: ARM926EJ-S
• Data Bus Width: 32 bit
• Data Ram Size: 256 KB
• Interface Type: I2C, I2S, UART, USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 51
• Number Of Timers: 6
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 568-4531; 935287119551

NXP Semiconductors
LPC3220_30_40_50_1
Product data sheet
7.7.4.4 Power control modes
7.7.4.5 Reset
7.8
output to be used directly. The maximum PLL output frequency supported by the CPU is
266 MHz. The only output frequency supported by the USB PLL is 48 MHz, and the clock
has strict requirements for nominal frequency (500 ppm) and jitter (500 ps).
The LPC3220/30/40/50 supports three operational modes, two of which are specifically
designed to reduce power consumption. The modes are: Run mode, Direct Run mode,
and Stop mode.
Run mode is the normal operating mode for applications that require the CPU, AHB bus,
or any peripheral function other than the USB block to run faster than the main oscillator
frequency. In Run mode, the CPU can run at up to 266 MHz and the AHB bus can run at
up to 133 MHz.
Direct Run mode allows reducing the CPU and AHB bus rates in order to save power.
Direct Run mode can also be the normal operating mode for applications that do not
require the CPU, AHB bus, or any peripheral function other than the USB block to run
faster than the main oscillator frequency. Direct Run mode is the default mode following
chip reset.
Stop mode causes all CPU and AHB operation to cease, and stops clocks to peripherals
other than the USB block.
Reset is accomplished by an active LOW signal on the RESET input pin. A reset pulse
with a minimum width of 10 main oscillator clocks after the oscillator is stable is required to
guarantee a valid chip reset. At power-up, 10 milliseconds should be allowed for the
oscillator to start up and stabilize after V
with a minimum duration of 10 clock pulses will also be applied if the watchdog timer
generates an internal device reset.
The RESET pin is located in the RTC power domain. This means that the RTC power
must be present for an external reset to have any effect. The RTC power domain
nominally runs from 1.2 V, but the RESET pin can be driven as high as 1.95 V.
In addition to the Ethernet MAC and USB interfaces there are many more serial
communication peripheral interfaces available on the LPC3220/30/40/50. Here is a list of
the serial communication interfaces:
A short functional description of each of these peripherals is provided in the following
sections.
Communication peripheral interfaces
•
•
•
•
•
Seven UARTs; four standard UARTs and three high-speed UARTs
Two SPI serial I/O controllers
Two SSP serial I/O controllers
Two I
Two I
2
2
C serial I/O controllers
S audio controllers
All information provided in this document is subject to legal disclaimers.
Rev. 01.03 — 16 March 2010
DD
reaches operational voltage. An internal reset
LPC3220/30/40/50
16/32-bit ARM microcontrollers
© NXP B.V. 2010. All rights reserved.
35 of 77