EP9315-CBZ Cirrus Logic Inc, EP9315-CBZ Datasheet - Page 138

• Manufacturer Part Number: EP9315-CBZ
• Description: IC ARM9 SOC ENH UNIV 352PBGA
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9315-CBZ

• Core Size: 16/32-Bit
• Core Processor: ARM9
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, PCMCIA, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 352-BGA
• Controller Family/series: (ARM9)
• No. Of I/o's: 16
• Cpu Speed: 200MHz
• No. Of Timers: 5
• Digital Ic Case Style: BGA
• Supply Voltage Range: 1.65V To 1.94V, 3V To 3.6V
• Embedded Interface Type: SPI
• Rohs Compliant: Yes
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: EDB9315A-Z
• Case: BGA
• Dc: 06+
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1144 - KIT DEVELOPMENT EP9315 ARM9
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 598-1139

5
5-12
5.1.6.2.3
5.1.6.2.4
5.1.6.2.5
System Controller
EP93xx User’s Guide
5.1.7 Interrupt Generation
set. One example of this is when a power-on-reset is applied and this register bit is cleared.
This means that this bit will not be set on boot-up and will have to be set to maintain the
memory image for when the device re-enters Standby mode.
A transition from Run mode to Halt mode is caused by reading the Halt register location
0x8093_0008 with the SHena bit set to 1. This has the effect of gating the CPU clock (FCLK)
bus interface, with the APB/AHB system clock, and Memory/DMA system remaining enabled.
There are normally several conditions in which the device can move from Standby mode to
Run mode.
These conditions are:
The EP93xx comes out of Standby if an interrupt occurs or when an exit from a ClkSet1 write
occurs. If a write is performed to the ClkSet1 register, the EP93xx then enters Standby mode
and then automatically comes out of Standby mode and back into the Run state.
The transition from the Halt state to the Run state is caused by:
The Syscon block generates two interrupts: TICK interrupt and Watchdog Expired interrupt.
The block generates the TICK interrupt based upon the 64 Hz clock, which is derived from
the 32.768 KHz oscillator. The interrupt becomes active on every rising edge of the internal
64 Hz clock. It can be cleared by writing to the TEOI location.
Watchdog Expired interrupt becomes active on a rising edge of the 64 Hz TICK clock, if the
TICK interrupt is still active. In other words, if a TICK interrupt has not been served for a
complete TICK period, a watchdog expired interrupt is generated. It can be cleared by writing
to the TEOI location as well.
• A falling edge on IRQ interrupt
• A falling edge on FIQ interrupt
• An exit from a
• PRSTn
• RSTOn
• A falling edge on IRQ interrupt
• A falling edge on FIQ interrupt
• RSTOn
RUN HALT mode
STANDBY RUN mode
HALT RUN mode
"ClkSet1"
write
Copyright 2007 Cirrus Logic
DS785UM1