AT91M55800A-33CJ Atmel, AT91M55800A-33CJ Datasheet - Page 13

• Manufacturer Part Number: AT91M55800A-33CJ
• Description: IC ARM MCU 16BIT 176BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M55800A-33CJ

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 58
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 176-LFBGA
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: EBI, SPI, USART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 58
• Number Of Timers: 10 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91EB55
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• Cpu Family: AT91
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 33MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 8KB
• # I/os (max): 58
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 176
• Package Type: BGA
• For Use With: AT91EB55 - KIT EVAL FOR ARM AT91M55800A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7. Product Overview
7.1
7.2
1745F–ATARM–06-Sep-07
Power Supplies
Input/Output Considerations
The AT91M55800A has 5 kinds of power supply pins:
VDDIO and VDDCORE are separated to permit the I/O lines to be powered with 5V, thus result-
ing in full TTL compliance.
The following ground pins are provided:
All of these ground pins must be connected to the same voltage (generally the board electric
ground) with wires as short as possible. GNDPLL, GNDA and GNDBU are provided separately
in order to allow the user to add a decoupling capacitor directly between the power and ground
pads. In the same way, the PLL filter resistor and capacitors must be connected to the device
and to GNDBU with wires as short as possible. Also, the main oscillator crystal and the 32768
Hz crystal external load capacitances must be connected respectively to GNDPLL and to
GNDBU with wires as short as possible.
The main constraints applying to the different voltages of the device are:
The nominal power combinations supported by the AT91M55800A are described in the following
table:
Table 7-1.
After the reset, the peripheral I/Os are initialized as inputs to provide the user with maximum
flexibility. It is recommended that in any application phase, the inputs to the AT91M55800A
microcontroller be held at valid logic levels to minimize the power consumption.
• VDDCORE pins, which power the chip core
• VDDIO pins, which power the I/O Lines
• VDDPLL pins, which power the oscillator and PLL cells
• VDDA pins, which power the analog peripherals ADC and DAC
• VDDBU pins, which power the RTC, the 32768 Hz oscillator and the Shut-down Logic of the
• GND for both VDDCORE and VDDIO
• GNDPLL for VDDPLL
• GNDA for VDDA
• GNDBU for VDDBU
• VDDBU must be lower than or equal to VDDCORE
• VDDA must be higher than or equal to VDDCORE
• VDDCORE must be lower than or equal to VDDIO
APMC
VDDIO
3.3V
3V
5V
Nominal Power Combinations
VDDCORE
3.3V
3.3V
3V
VDDA
3.3V
3.3V
3V
VDDPLL
3.3V
3.3V
3V
VDDBU
3.3V
3.3V
3V
AT91M5880A
Maximum Operating
Frequency
33 MHz
33 MHz
33 MHz
13