AT91M55800A-33CJ Atmel, AT91M55800A-33CJ Datasheet - Page 197

• Manufacturer Part Number: AT91M55800A-33CJ
• Description: IC ARM MCU 16BIT 176BGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91M55800A-33CJ

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: POR, WDT
• Number Of I /o: 58
• Program Memory Type: ROMless
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 176-LFBGA
• Processor Series: AT91Mx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 8 KB
• Interface Type: EBI, SPI, USART
• Maximum Clock Frequency: 33 MHz
• Number Of Programmable I/os: 58
• Number Of Timers: 10 bit
• Operating Supply Voltage: 3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91EB55
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 8 Channel
• On-chip Dac: 8 bit, 2 Channel
• Cpu Family: AT91
• Device Core: ARM7TDMI
• Device Core Size: 32b
• Frequency (max): 33MHz
• Program Memory Size: Not Required
• Total Internal Ram Size: 8KB
• # I/os (max): 58
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 176
• Package Type: BGA
• For Use With: AT91EB55 - KIT EVAL FOR ARM AT91M55800A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Figure 20-6. Programmable Delays (DLYBCS, DLYBS and DLYBCT)
20.5
20.6
1745F–ATARM–06-Sep-07
SPCK Output
Chip Select 2
Chip Select 1
Clock Generation
Peripheral Data Controller
In master mode the SPI Master Clock is either MCK or MCK/32, as defined by the MCK32 field
of SP_MR. The SPI baud rate clock is generated by dividing the SPI Master Clock by a value
between 4 and 510. The divisor is defined in the SCBR field in each Chip Select Register. The
transfer speed can thus be defined independently for each chip select signal.
CPOL and NCPHA in the Chip Select Registers define the clock/data relationship between mas-
ter and slave devices. CPOL defines the inactive value of the SPCK. NCPHA defines which
edge causes data to change and which edge causes data to be captured.
In Slave Mode, the input clock low and high pulse duration must strictly be longer than two sys-
tem clock (MCK) periods.
The SPI is closely connected to two Peripheral Data Controller channels. One is dedicated to
the receiver. The other is dedicated to the transmitter.
The PDC channel is programmed using SP_TPR (Transmit Pointer) and SP_TCR (Transmit
Counter) for the transmitter and SP_RPR (Receive Pointer) and SP_RCR (Receive Counter) for
the receiver. The status of the PDC is given in SP_SR by the SPENDTX bit for the transmitter
and by the SPENDRX bit for the receiver.
The pointer registers (SP_TPR and SP_RPR) are used to store the address of the transmit or
receive buffers. The counter registers (SP_TCR and SP_RCR) are used to store the size of
these buffers.
The receiver data transfer is triggered by the RDRF bit and the transmitter data transfer is trig-
gered by TDRE. When a transfer is performed, the counter is decremented and the pointer is
incremented. When the counter reaches 0, the status bit is set (SPENDRX for the receiver,
SPENDTX for the transmitter in SP_SR) and can be programmed to generate an interrupt. While
the counter is at zero, the status bit is asserted and transfers are disabled.
Change peripheral
DLYBCS
DLYBS
of peripheral
No change
DLYBCT
AT91M5880A
DLYBCT
197