MC68HC16Z1CAG25 Freescale Semiconductor, MC68HC16Z1CAG25 Datasheet - Page 295

• Manufacturer Part Number: MC68HC16Z1CAG25
• Description: IC MCU 16BIT 25MHZ 144-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HC16r

Specifications of MC68HC16Z1CAG25

• Core Processor: CPU16
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LQFP
• Cpu Family: HC16
• Device Core Size: 16b
• Frequency (max): 25MHz
• Interface Type: SCI/SPI/UART
• Program Memory Size: Not Required
• Total Internal Ram Size: 1KB
• # I/os (max): 16
• Number Of Timers - General Purpose: 11
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 8-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 144
• Package Type: LQFP
• Controller Family/series: 68HC16
• No. Of I/o's: 16
• Ram Memory Size: 1KB
• Cpu Speed: 25MHz
• No. Of Timers: 2
• Embedded Interface Type: QSPI, SCI
• Rohs Compliant: Yes
• Processor Series: HC16Z
• Core: CPU16
• Data Bus Width: 16 bit
• Data Ram Size: 1 KB
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 11
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: Compliant

M68HC16 Z SERIES
USER’S MANUAL
Num
17
18
19
NOTES:
10. When V
11. Power dissipation measured at specified system clock frequency, all modules active. Power dissipation can be
1. Applies to:
2. Input-Only Pins: EXTAL, TSC, BKPT/DSCLK, PAI, PCLK, RXD
3. Does not apply to HALT and RESET because they are open drain pins.
4. Use of an active pulldown device is recommended.
5. Total operating current is the sum of the appropriate I
6. Current measured with system clock frequency of 16.78 MHz, all modules active.
7. This parameter is periodically sampled rather than 100% tested.
8. CPU16 in WAIT, all other modules inactive.
9. The RAM module will not switch into standby mode as long as V
the V
ification. System noise on the V
calculated using the expression:
I
Output-Only Pins: CSBOOT, BG/CS1, CLKOUT, FREEZE/QUOT, DSO/IPIPE0, PWMA, PWMB
Input/Output Pins:
Does not apply to port MCCI[7:0] (TXD, PCS[3:1], PCS0/SS, SCK, MOSI, MISO) in wired-OR mode.
The RAM array cannot be accessed while the module is in standby mode.
DD
MC68CM16Z1/Z4 Power Dissipation
Input Capacitance
Load Capacitance
Port ADA [7:0] — AN[7:0]
Port E [7:4] — SIZ[1:0], AS, DS
Port F [7:0] — IRQ[7:1], MODCLK
Port GP[7:0] — IC4/OC5/OC1, IC[3:1], OC[4:1]/OC1
Port MCCI[7:0] — TXD, PCS[3:1], PCS0/SS, SCK, MOSI, MISO
BKPT/DSCLK, DSI/IPIPE1, PAI, PCLK, RESET, RXD, TSC
All input-only pins
All input/output pins
Group 1 I/O Pins, CLKOUT, FREEZE/QUOT, IPIPE0
Group 2 I/O Pins and CSBOOT, BG/CS
Group 3 I/O Pins
Group 4 I/O Pins
includes supply currents for all device modules powered by V
Table A-11 Low Voltage 16.78-MHz DC Characteristics (Continued)
STBY
DD
and V
is transitioning during a power up or power down sequence, and V
Group 1: Port GP[7:0] — IC4/OC5/OC1, IC[3:1], OC[4:1]/OC1, DATA[15:0], DSI/IPIPE1
Group 2: Port C[6:0] — ADDR[22:19]/CS[9:6], FC[2:0]/CS[5:3]
Group 3: HALT, RESET
Group 4: MISO, MOSI, SCK
DD
(V
pins, which causes standby current to increase toward the maximum transient condition spec-
2, 7
2
Port E[7:0] — SIZ[1:0], AS, DS, AVEC, DSACK[1:0]
Port F[7:0] — IRQ[7:1], MODCLK
Port MCCI[7:3] — TXD, PCS[3:1], PCS0/SS, ADDR23/CS10/ECLK
P
DD
D
= Maximum V
and V
Freescale Semiconductor, Inc.
For More Information On This Product,
Characteristic
DDSYN
DD
ELECTRICAL CHARACTERISTICS
and V
Go to: www.freescale.com
= 2.7 to 3.6Vdc, V
11
DD
STBY
(I
DD
pins can contribute to this condition.
+ I
DDSYN
DD
+ I
, I
SS
SB
DDSYN
) + Maximum V
= 0 Vdc, T
SB
, I
DD
SB
does not exceed V
pins.
, and I
Symbol
A
P
C
C
= T
D
in
L
DDA
SB
DDA
L
is applied, current flows between
.
to T
(I
DDA
H
Min
—
—
—
—
—
—
—
)
)
DD
by more than 0.5 Volt.
Max
191
100
100
100
10
20
90
Unit
mW
A-11
pF
pF