R4F24268NVFQV Renesas Electronics America, R4F24268NVFQV Datasheet - Page 992

• Manufacturer Part Number: R4F24268NVFQV
• Description: MCU 256K FLASH 48K 144-LQFP
• Manufacturer: Renesas Electronics America
• Series: H8® H8S/2400r

Specifications of R4F24268NVFQV

• Core Processor: H8S/2600
• Core Size: 16/32-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, I²C, IrDA, SCI, SSU, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 96
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: External
• Operating Temperature: -20°C ~ 75°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Section 16 I2C Bus Interface 2 (IIC2)
16.3.2
ICCRB is an 8-bit readable/writable register that issues start/stop conditions, manipulates the SDA
pin, monitors the SCL pin, and controls reset in I
Page 962 of 1372
Bit
7
6
5
4
3
2
Bit Name
BBSY
SCP
SDAO
⎯
SCLO
⎯
I
2
C Bus Control Register B (ICCRB)
0
1
1
1
1
1
Initial Value
R/W
R/W
R/W
R
R/W
R
⎯
Description
Bus Busy
This bit enables to confirm whether the I
occupied or released and to issue start and stop
conditions in master mode. This bit is set to 1
when the SDA level changes from high to low
under the condition of SCL = high, assuming that
the start condition has been issued. This bit is
cleared to 0 when the SDA level changes from low
to high under the condition of SCL = high,
assuming that the stop condition has been issued.
Write 1 to BBSY and 0 to SCP to issue a start
condition. Follow this procedure when also re-
transmitting a start condition. Write 0 to BBSY and
0 to SCP to issue a stop condition. To issue a
start/stop condition, use the MOV instruction.
Start Condition/Stop Condition Prohibit
The SCP bit controls the issue of start/stop
conditions in master mode.
To issue a start condition, write 1 in BBSY and 0
in SCP. A retransmit start condition is issued in
the same way. To issue a stop condition, write 0 in
BBSY and 0 in SCP. This bit is always read as 1.
If 1 is written, the data is not stored.
This bit monitors SDA output level. When reading
and SDA0 is 1, the SDA pin outputs high. When
reading and SDA0 is 0, the SDA pin outputs low.
The write value should always be 1.
Reserved
The write value should always be 1.
This bit monitors SCL output level. When reading
and SCLO is 1, the SCL pin outputs high. When
reading and SCLO is 0, the SCL pin outputs low.
Reserved
This bit is always read as 1.
2
C control.
H8S/2426, H8S/2426R, H8S/2424 Group
REJ09B0466-0350 Rev. 3.50
2
C bus is
Jul 09, 2010