AT91SAM7SE256-CU Atmel, AT91SAM7SE256-CU Datasheet - Page 595

• Manufacturer Part Number: AT91SAM7SE256-CU
• Description: IC ARM7 MCU FLASH 256K 144-LFBGA
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7SE256-CU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 55MHz
• Connectivity: EBI/EMI, I²C, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 88
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 144-LFBGA
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: EBI, SPI, TWI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.3 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, KSK-AT91SAM7S-PL, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7SE-EK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: AT91SAM7SE-EK - EVAL BOARD FOR AT91SAM7SEAT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: AT91SAM7SE256-CJ; AT91SAM7SE256-CJ

38.6.12
Name:
Access:
WARNING: The UDP peripheral clock in the Power Management Controller (PMC) must be enabled before any read/write
operations to the UDP registers including the UDP_TXVC register.
• TXVDIS: Transceiver Disable
When UDP is disabled, power consumption can be reduced significantly by disabling the embedded transceiver. This can
be done by setting TXVDIS field.
To enable the transceiver, TXVDIS must be cleared.
• PUON: Pullup On
0: The 1.5KΩ integrated pullup on DDP is disconnected.
1: The 1.5 KΩ integrated pullup on DDP is connected.
NOTE: If the USB pullup is not connected on DDP, the user should not write in any UDP register other than the UDP_TXVC
register. This is because if DDP and DDM are floating at 0, or pulled down, then SE0 is received by the device with the con-
sequence of a USB Reset.
6222F–ATARM–14-Jan-11
31
23
15
–
–
–
7
–
UDP Transceiver Control Register
30
22
14
UDP_TXVC
–
–
–
6
–
Read-write
29
21
13
–
–
–
5
–
28
20
12
–
–
–
4
–
SAM7SE512/256/32 Preliminary
27
19
11
–
–
–
3
–
26
18
10
–
–
–
2
–
PUON
25
17
–
–
9
1
–
TXVDIS
24
16
–
–
8
0
–
595