AD9992_07 AD [Analog Devices], AD9992_07 Datasheet - Page 90

• Manufacturer Part Number: AD9992_07
• Description: 12-Bit CCD Signal Processor with Precision Timing Generator
• Manufacturer: AD [Analog Devices]

AD9992
Address
0x1F
0x20
0x21
0x22
0x23
0x24
0x25
0x26
0x27
Table 42. Field Registers
Address
0x00
0x01
Data
Bits
[12:0]
[25:13]
[12:0]
[13]
[14]
[17:15]
[2:0]
[6:4]
[10:8]
[14:12]
[18:16]
[22:20]
[12:0]
[25:13]
[12:0]
[25:13]
[12:0]
[25:13]
[12:0]
[25:13]
[12:0]
[25:13]
[12:0]
[25:13]
Data
Bits
[4:0]
[9:5]
[14:10]
[19:15]
[24:20]
[4:0]
[9:5]
[14:10]
[19:15]
[21:20]
[23:22]
[25:24]
Default
Value
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Default
Value
X
X
X
X
X
X
X
X
X
Update
Type
SCP
SCP
SCP
SCP
SCP
SCP
SCP
SCP
SCP
VD
VD
Update
Type
Mnemonic
HBLKSTARTA
HBLKSTARTB
HBLKSTARTC
VSEQALT_EN
VALT_MAP
SPC_PAT_EN
HBLKALT_PAT1
HBLKALT_PAT2
HBLKALT_PAT3
HBLKALT_PAT4
HBLKALT_PAT5
HBLKALT_PAT6
CLPOBTOG1
CLPOBTOG2
PBLKTOG1
PBLKTOG2
LASTREPLEN_A
LASTREPLEN_B
LASTREPLEN_C
LASTREPLEN_D
LASTTOG_A
LASTTOG_B
LASTTOG_C
LASTTOG_D
Mnemonic
SEQ0
SEQ1
SEQ2
SEQ3
SEQ4
SEQ5
SEQ6
SEQ7
SEQ8
MULT_SWEEP0
MULT_SWEEP1
MULT_SWEEP2
Rev. C | Page 90 of 92
Description
HBLK Repeat Area Start Position A for HBLK Mode 2. Set to 8191 if not used.
HBLK Repeat Area Start Position B for HBLK Mode 2. Set to 8191 if not used.
HBLK Repeat Area Start Position C for HBLK Mode 2. Set to 8191 if not used.
Special V-sequence alternation enable.
1: Enables operation of VALTSEL0_EVEN/ODD, VALTSEL1_EVEN/ODD
registers in FREEZE/RESUME registers. Must be enabled if special VALT mode
is used.
1: Enables use of special vertical pattern insertion into VPATA sequence.
[0]: Use VPATB as the special pattern.
[1]: Use VPATC as the special pattern.
[2]: Use VPATD as the special pattern.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
HBLK Mode 2, Repeat Area 0 pattern for odd lines.
CLPOB Toggle Position 1.
CLPOB Toggle Position 2.
PBLK Toggle Position 1.
PBLK Toggle Position 2.
Last repetition length for Group A. Set equal to VLENA.
Last repetition length for Group B. Set equal to VLENB.
Last repetition length for Group C. Set equal to VLENC.
Last repetition length for Group D. Set equal to VLEND.
Optional fifth toggle position for Group A.
Optional fifth toggle position for Group B.
Optional fifth toggle position for Group C.
Optional fifth toggle position for Group D.
Description
Selected V-sequence for first region in the field.
Selected V-sequence for second region in the field.
Selected V-sequence for third region in the field.
Selected V-sequence for fourth region in the field.
Selected V-sequence for fifth region in the field.
Selected V-sequence for sixth region in the field.
Selected V-sequence for seventh region in the field.
Selected V-sequence for eighth region in the field.
Selected V-sequence for ninth region in the field.
Enables multiplier mode and/or sweep mode for Region 0:
0: Multiplier off/sweep off.
1: Multiplier off/sweep on.
2: Multiplier on/sweep off.
3: Multiplier on/sweep on.
Enables multiplier mode and/or sweep mode for Region 2.
Enables multiplier mode and/or sweep mode for Region 1.