PEB20534H-10 SIEMENS [Siemens Semiconductor Group], PEB20534H-10 Datasheet - Page 347
![no-image](/images/no-image-200.jpg)
PEB20534H-10
Manufacturer Part Number
PEB20534H-10
Description
DMA Supported Serial Communication Controller with 4 Channels DSCC4
Manufacturer
SIEMENS [Siemens Semiconductor Group]
Datasheet
1.PEB20534H-10.pdf
(442 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
INF
Quantity:
5 510
Company:
Part Number:
PEB20534H-10-V2.1
Manufacturer:
PHILIPS
Quantity:
5 510
Company:
Part Number:
PEB20534H-10V2.1
Manufacturer:
MICRON
Quantity:
78
- Current page: 347 of 442
- Download datasheet (2Mb)
Semiconductor Group
FERR
SCD
PLLA
CDSC
RFO
Framing Error Interrupt
This bit is set to ’1’, if a character framing error is detected, i.e. a ’0’ was
ampled at a position where a stop bit ’1’ was expected due to the
selected character format.
SYN Character Detected Interrupt
This bit is set to ’1’, if a synchronization character (SYNC) was detected
after the receiver was switched to HUNT-mode (by command bit ’HUNT’
in register CMDR).
DPLL Asynchronous Interrupt
This bit is only valid, if the receive clock is derived from the internal DPLL
and FM0, FM1 or Manchester data encoding is selected (depending on
the selected clock mode and data encoding mode). It is set to ’1’ if the
DPLL
synchronization has been regained again. If the transmitter is supplied
with a clock derived from the DPLL, transmission is also interrupted.
Carrier Detect Status Change Interrupt
This bit is set to ’1’, if a state transition has been detected at signal CD.
Because only a state transition is indicated via this interrupt, the current
status can be evaluated by reading bit ’CD’ in status register STAR.
Receive FIFO Overflow Interrupt
HDLC Mode:
This bit is set to ’1’, if the SCC receive FIFO is full and a complete frame
must be discarded. This interrupt can be used for statistical purposes
and might indicate that the DMAC was not able to service the SCC
receive FIFO quickly enough, e.g. PCI bus latencies are too bad.
ASYNC/BISYNC Mode:
This bit is set to ’1’, if the SCC receive FIFO is full and another received
character must be discarded. This interrupt can be used for statistical
purposes and might indicate that the DMAC was not able to service the
SCC receive FIFO quickly enough, e.g. PCI bus latencies are too bad.
has
lost
synchronization.
347
Reception
Detailed Register Description
is
disabled
Data Sheet 09.98
(bisync mode)
(async mode)
PEB 20534
(all modes)
(all modes)
(all modes)
until
Related parts for PEB20534H-10
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![S80C32-12](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
![BAT14-033](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon Schottky Diode (HiRel Discrete and Microwave Semiconductor Medium barrier diodes for detector and mixer applications)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY43-P1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BXY44-T1](/images/no-image3.png)
Part Number:
Description:
HiRel Silicon PIN Diode (HiRel Discrete and Microwave Semiconductor Current controlled RF resistor for RF attenuators and switches)
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL80](/images/no-image3.png)
Part Number:
Description:
GaAs-Infrarot-Sendediode GaAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![IRL81](/images/no-image3.png)
Part Number:
Description:
GaAlAs-Infrarot-Sendediode GaAlAs Infrared Emitter
Manufacturer:
SIEMENS [Siemens Semiconductor Group]
Datasheet:
![BSM50GB100D](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM181R](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM254F](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BSM111AR](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![BUZ48](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![TDA4716C](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![DL440M](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
![SDA5255](/images/manufacturer_photos/0/6/607/siemens_semiconductor_group_tmb.jpg)
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet: