MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 24

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.3
The Program Counter (PC) is 13 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<12:8>) is not directly
readable or writable and comes from PCLATH. On any
Reset, the PC is cleared. Figure 2-5 shows the two
situations for the loading of the PC. The upper example
in Figure 2-5 shows how the PC is loaded on a write to
PCL (PCLATH<4:0> → PCH). The lower example in
Figure 2-5 shows how the PC is loaded during a CALL or
GOTO instruction (PCLATH<4:3> → PCH).
FIGURE 2-5:
2.3.1
Executing any instruction with the PCL register as the
destination simultaneously causes the Program
Counter PC<12:8> bits (PCH) to be replaced by the
contents of the PCLATH register. This allows the entire
contents of the program counter to be changed by
writing the desired upper 5 bits to the PCLATH register.
When the lower 8 bits are written to the PCL register,
all 13 bits of the program counter will change to the
values contained in the PCLATH register and those
being written to the PCL register.
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). Care should be
exercised when jumping into a look-up table or
program branch table (computed GOTO) by modifying
the PCL register. Assuming that PCLATH is set to the
table start address, if the table length is greater than
255 instructions or if the lower 8 bits of the memory
address rolls over from 0xFF to 0x00 in the middle of
the table, then PCLATH must be incremented for each
address rollover that occurs between the table
beginning and the target location within the table.
For more information refer to Application Note AN556,
“Implementing a Table Read” (DS00556).
PIC16F610/616/16HV610/616
PC
PC
DS41288F-page 24
12
12 11 10
2
PCL and PCLATH
5
PCH
PCLATH<4:3>
PCH
MODIFYING PCL
PCLATH
PCLATH<4:0>
8
PCLATH
8
7
7
LOADING OF PC IN
DIFFERENT SITUATIONS
PCL
PCL
11
8
0
0
OPCODE <10:0>
ALU Result
GOTO, CALL
Instruction with
Destination
PCL as
2.3.2
The PIC16F610/616/16HV610/616 Family has an
8-level x 13-bit wide hardware stack (see Figure 2-1).
The stack space is not part of either program or data
space and the Stack Pointer is not readable or writable.
The PC is PUSHed onto the stack when a CALL
instruction is executed or an interrupt causes a branch.
The stack is POPed in the event of a RETURN, RETLW
or a RETFIE instruction execution. PCLATH is not
affected by a PUSH or POP operation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
2.4
The INDF register is not a physical register. Addressing
the INDF register will cause indirect addressing.
Indirect addressing is possible by using the INDF
register. Any instruction using the INDF register
actually accesses data pointed to by the File Select
Register (FSR). Reading INDF itself indirectly will
produce 00h. Writing to the INDF register indirectly
results in a no operation (although Status bits may be
affected). An effective 9-bit address is obtained by
concatenating the 8-bit FSR and the IRP bit of the
STATUS register, as shown in Figure 2-7.
A simple program to clear RAM location 40h-4Fh using
indirect addressing is shown in Example 2-1.
EXAMPLE 2-1:
NEXT
CONTINUE
Note 1: There are no Status bits to indicate stack
2: There are no instructions/mnemonics
Indirect Addressing, INDF and
FSR Registers
MOVLW
MOVWF
CLRF
INCF
BTFSS
GOTO
STACK
overflow or stack underflow conditions.
called PUSH or POP. These are actions
that occur from the execution of the
CALL, RETURN, RETLW and RETFIE
instructions or the vectoring to an
interrupt address.
0x40
FSR
INDF
FSR, F ;inc pointer
FSR,4
NEXT
INDIRECT ADDRESSING
© 2009 Microchip Technology Inc.
;initialize pointer
;to RAM
;clear INDF register
;all done?
;no clear next
;yes continue