MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 49

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

6.0
The Timer1 module is a 16-bit timer/counter with the
following features:
• 16-bit timer/counter register pair (TMR1H:TMR1L)
• Programmable internal or external clock source
• 3-bit prescaler
• Optional LP oscillator
• Synchronous or asynchronous operation
• Timer1 gate (count enable) via comparator or
• Interrupt on overflow
• Wake-up on overflow (external clock,
• Time base for the Capture/Compare function
• Special Event Trigger (with ECCP)
• Comparator output synchronization to Timer1
Figure 6-1 is a block diagram of the Timer1 module.
FIGURE 6-1:
© 2009 Microchip Technology Inc.
T1G pin
Asynchronous mode only)
clock
Without CLKOUT
OSC1/T1CKI
OSC2/T1G
TIMER1 MODULE WITH GATE
CONTROL
T1OSCEN
Note 1:
INTOSC
Set flag bit
TMR1IF on
Overflow
2:
3:
ST Buffer is low power type when using LP osc, or high speed type when using T1CKI.
Timer1 register increments on rising edge.
Synchronize does not operate while in Sleep.
TIMER1 BLOCK DIAGRAM
Oscillator
TMR1H
TMR1
(2)
TMR1L
PIC16F610/616/16HV610/616
Internal
F
OSC
Clock
F
OSC
EN
/4
(1)
T1ACS
1
0
6.1
The Timer1 module is a 16-bit incrementing counter
which is accessed through the TMR1H:TMR1L register
pair. Writes to TMR1H or TMR1L directly update the
counter.
When used with an internal clock source, the module is
a timer. When used with an external clock source, the
module can be used as either a timer or counter.
6.2
The TMR1CS bit of the T1CON register is used to select
the clock source. When TMR1CS = 0, the clock source
is F
supplied externally.
F
F
T1CKI pin
TMR1CS
Clock Source
OSC
OSC
0
1
To C2 Comparator Module
Timer1 Clock
OSC
/4
/4. When TMR1CS = 1, the clock source is
Timer1 Operation
Clock Source Selection
T1CKPS<1:0>
T1SYNC
Prescaler
1, 2, 4, 8
TMR1ON
0
1
2
C2OUT
TMR1CS
TMR1GE
0
0
1
Synchronized
Synchronize
clock input
T1GSS
1
0
det
DS41288F-page 49
(3)
T1ACS
T1GINV
0
1
x