MCP1631RD-DCPC1 Microchip Technology, MCP1631RD-DCPC1 Datasheet - Page 88

• Manufacturer Part Number: MCP1631RD-DCPC1
• Description: REF DES BATT CHARG OR LED DRIVER
• Manufacturer: Microchip Technology

Specifications of MCP1631RD-DCPC1

• Current - Output / Channel: 700mA
• Outputs And Type: 1, Non-Isolated
• Features: Firmware for Li-Ion, NiMH, and NiCd Battery Charger
• Voltage - Input: 3.5 ~ 16 V
• Utilized Ic / Part: MCP1631HV, PIC16F616
• Core Chip: MCP1631HV, PIC16F616
• Topology: Parallel, Series
• Output Current: 1A
• No. Of Outputs: 1
• Input Voltage: 3.5V To 16V
• Dimming Control Type: Analog
• Kit Contents: Board
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Voltage - Output: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F610/616/16HV610/616
10.2
In Compare mode, the 16-bit CCPR1 register value is
constantly compared against the TMR1 register pair
value. When a match occurs, the CCP1 module may:
• Toggle the CCP1 output
• Set the CCP1 output
• Clear the CCP1 output
• Generate a Special Event Trigger
• Generate a Software Interrupt
The action on the pin is based on the value of the
CCP1M<3:0> control bits of the CCP1CON register.
All Compare modes can generate an interrupt.
FIGURE 10-2:
10.2.1
The user must configure the CCP1 pin as an output by
clearing the associated TRIS bit.
DS41288F-page 88
Note:
CCP1
Pin
Special Event Trigger will:
• Clear TMR1H and TMR1L registers.
• NOT set interrupt flag bit TMR1IF of the PIR1 register.
• Set the GO/DONE bit to start the ADC conversion.
Output Enable
TRIS
Compare Mode
CCP1 PIN CONFIGURATION
Clearing the CCP1CON register will force
the CCP1 compare output latch to the
default low level. This is not the PORT I/O
data latch.
Q
Special Event Trigger
CCP1CON<3:0>
R
S
Mode Select
Output
COMPARE MODE
OPERATION BLOCK
DIAGRAM
Logic
Set CCP1IF Interrupt Flag
4
(PIR1)
Match
CCPR1H CCPR1L
TMR1H
Comparator
TMR1L
10.2.2
In Compare mode, Timer1 must be running in either
Timer mode or Synchronized Counter mode. The
compare operation may not work in Asynchronous
Counter mode.
10.2.3
When Generate Software Interrupt mode is chosen
(CCP1M<3:0> = 1010), the CCP1 module does not
assert control of the CCP1 pin (see the CCP1CON
register).
10.2.4
When Special Event Trigger mode is chosen
(CCP1M<3:0> = 1011), the CCP1 module does the
following:
• Resets Timer1
• Starts an ADC conversion if ADC is enabled
The CCP1 module does not assert control of the CCP1
pin in this mode (see the CCP1CON register).
The Special Event Trigger output of the CCP occurs
immediately upon a match between the TMR1H,
TMR1L register pair and the CCPR1H, CCPR1L
register pair. The TMR1H, TMR1L register pair is not
reset until the next rising edge of the Timer1 clock. This
allows the CCPR1H, CCPR1L register pair to
effectively provide a 16-bit programmable period
register for Timer1.
Note 1: The Special Event Trigger from the CCP
2: Removing
TIMER1 MODE SELECTION
SOFTWARE INTERRUPT MODE
SPECIAL EVENT TRIGGER
module does not set interrupt flag bit
TMR1IF of the PIR1 register.
changing the contents of the CCPR1H
and CCPR1L register pair, between the
clock edge that generates the Special
Event Trigger and the clock edge that
generates the Timer1 Reset, will preclude
the Reset from occurring.
© 2009 Microchip Technology Inc.
the
match
condition
by