DV164136 Microchip Technology, DV164136 Datasheet - Page 215

• Manufacturer Part Number: DV164136
• Description: DEVELOPMENT KIT FOR PIC18
• Manufacturer: Microchip Technology
• Series: PIC®r
• Type: MCUr

Specifications of DV164136

• Contents: Board, Cables, CDs, PICkit™ 3 Programmer, Power Supply
• Processor To Be Evaluated: PIC18F8722, PIC18F87J11
• Interface Type: RS-232, USB
• Operating Supply Voltage: 3.3 V, 5 V
• Silicon Manufacturer: Microchip
• Core Architecture: PIC
• Core Sub-architecture: PIC18
• Silicon Core Number: PIC18F
• Silicon Family Name: PIC18F8xxx
• Kit Contents: PIC18 Exp Brd PICkit 3 Cable CD PSU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: PIC18F8722, PIC18F87J11
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

19.3.8
In SPI Master mode, module clocks may be operating
at a different speed than when in full power mode; in
the case of the Sleep mode, all clocks are halted.
In Idle modes, a clock is provided to the peripherals.
That clock can be from the primary clock source, the
secondary clock (Timer1 oscillator) or the INTOSC
source. See Section 2.7 “Clock Sources and
Oscillator Switching” for additional information.
In most cases, the speed that the master clocks SPI
data is not important; however, this should be
evaluated for each system.
If MSSP interrupts are enabled, they can wake the con-
troller from Sleep mode, or one of the Idle modes, when
the master completes sending data. If an exit from
Sleep or Idle mode is not desired, MSSP interrupts
should be disabled.
If the Sleep mode is selected, all module clocks are
halted and the transmission/reception will remain in
that state until the devices wakes. After the device
returns to Run mode, the module will resume
transmitting and receiving data.
In SPI Slave mode, the SPI Transmit/Receive Shift
register operates asynchronously to the device. This
allows the device to be placed in any power-managed
mode and data to be shifted into the SPI Trans-
mit/Receive Shift register. When all 8 bits have been
received, the MSSP interrupt flag bit will be set and if
enabled, will wake the device.
19.3.9
A Reset disables the MSSP module and terminates the
current transfer.
© 2008 Microchip Technology Inc.
OPERATION IN POWER-MANAGED
MODES
EFFECTS OF A RESET
19.3.10
Table 19-1 shows the compatibility between the
standard SPI modes and the states of the CKP and
CKE control bits.
TABLE 19-1:
There is also an SMP bit which controls when the data
is sampled.
19.3.11
Because MSSP1 and MSSP2 are independent
modules, they can operate simultaneously at different
data rates. Setting the SSPM3:SSPM0 bits of the
SSPxCON register determines the rate for the
corresponding module.
An exception is when both modules use Timer2 as a
time base in Master mode. In this instance, any
changes to the Timer2 module’s operation will affect
both MSSP modules equally. If different bit rates are
required for each module, the user should select one of
the other three time base options for one of the
modules.
PIC18F8722 FAMILY
Standard SPI Mode
Terminology
0, 0
0, 1
1, 0
1, 1
BUS MODE COMPATIBILITY
SPI CLOCK SPEED AND MODULE
INTERACTIONS
SPI BUS MODES
CKP
Control Bits State
0
0
1
1
DS39646C-page 213
CKE
1
0
1
0