EVAL-ADUC832QSZ Analog Devices Inc, EVAL-ADUC832QSZ Datasheet - Page 32

• Manufacturer Part Number: EVAL-ADUC832QSZ
• Description: KIT DEV FOR ADUC832 QUICK START
• Manufacturer: Analog Devices Inc
• Series: QuickStart™ Kitr
• Type: MCUr

Specifications of EVAL-ADUC832QSZ

• Contents: Evaluation Board, Cable, Power Supply, Software and Documentation
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With/related Products: ADuC832
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: EVAL-ADUC832QS; EVAL-ADUC832QS

ADuC832
USER INTERFACE TO OTHER ON-CHIP ADuC832
PERIPHERALS
The following section gives a brief overview of the various
peripherals also available on-chip. A summary of the SFRs used
to control and configure these peripherals is also given.
DAC
The ADuC832 incorporates two 12-bit voltage output DACs
on-chip. Each has a rail-to-rail voltage output buffer capable
of driving 10 kΩ/100 pF. Each has two selectable ranges, 0 V to
V
DACxH/L
Function
SFR Address
Power-On Default Value
Bit Addressable
The 12-bit DAC data should be written into DACxH/L right-justified such that DACxL contains the lower eight bits, and the lower
nibble of DACxH contains the upper four bits.
Bit
7
6
5
4
3
2
1
0
REF
(the internal band gap 2.5 V reference) and 0 V to AV
Name
MODE
RNG1
RNG0
CLR1
CLR0
SYNC
PD1
PD0
The DAC MODE bit sets the overriding operating mode for both DACs.
DAC0 Range Select Bit.
DAC0 Power-Down Bit.
Description
Set to “1” = 8-Bit Mode (Write 8 Bits to DACxL SFR).
Set to “0” = 12-Bit Mode.
DAC1 Range Select Bit.
Set to “1” = DAC1 Range 0–V
Set to “0” = DAC1 Range 0–V
Set to “1” = DAC0 Range 0–V
Set to “0” = DAC0 Range 0–V
DAC1 Clear Bit.
Set to “0” = DAC1 Output Forced to 0 V.
Set to “1” = DAC1 Output Normal.
DAC0 Clear Bit.
Set to “0” = DAC1 Output Forced to 0 V.
Set to “1” = DAC1 Output Normal.
DAC0/1 Update Synchronization Bit.
When set to “1,” the DAC outputs update as soon as DACxL SFRs are written. The user can
simultaneously update both DACs by first updating the DACxL/H SFRs while SYNC is “0.” Both
DACs will then update simultaneously when the SYNC bit is set to “1.”
DAC1 Power-Down Bit.
Set to “1” = Power-On DAC1.
Set to “0” = Power-Off DAC1.
Set to “1” = Power-On DAC0.
Set to “0” = Power-Off DAC0.
DAC Data Registers
DAC Data Registers, written by user to update the DAC output.
DAC0L (DAC0 Data Low Byte)
DAC0H (DAC0 Data High Byte)
00H
No
Table IX. DACCON SFR Bit Designations
DD
REF
DD
REF
DD
.
.
.
.
.
–32–
F9H; DAC1L (DAC1 Data Low Byte)
FAH; DAC1H(DAC1 Data High Byte)
All Four Registers
All Four Registers
Each can operate in 12-bit or 8-bit mode. Both DACs share a
control register, DACCON, and four data registers, DAC1H/L,
DAC0H/L. It should be noted that in 12-bit asynchronous mode,
the DAC voltage output will be updated as soon as the DACL
data SFR has been written; therefore, the DAC data registers
should be updated as DACH first, followed by DACL. Note:
for correct DAC operation on the 0 to V
must be switched on. This results in the DAC using the correct
reference value.
DACCON
SFR Address
Power-On Default Value
Bit Addressable
DAC Control Register
FDH
04H
No
REF
range, the ADC
FBH
FCH
REV. 0