SI1011-A-GM Silicon Laboratories Inc, SI1011-A-GM Datasheet - Page 176

• Manufacturer Part Number: SI1011-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1011-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1872-5

Si1010/1/2/3/4/5
16.2. High Power Applications
The dc-dc converter is designed to provide the system with 65 mW of output power, however, it can safely
provide up to 100 mW of output power without any risk of damage to the device. For high power applica-
tions, the system should be carefully designed to prevent unwanted VBAT and VDD_MCU/DC+ Supply
Monitor resets, which are more likely to occur when the dc-dc converter output power exceeds 65mW. In
addition, output power above 65 mW causes the dc-dc converter to have relaxed output regulation, high
output ripple and more analog noise. At high output power, an inductor with low DC resistance should be
chosen in order to minimize power loss and maximize efficiency.
The combination of high output power and low input voltage will result in very high peak and average
inductor currents. If the power supply has a high internal resistance, the transient voltage on the VBAT ter-
minal could drop below 0.9 V and trigger a VBAT Supply Monitor Reset, even if the open-circuit voltage is
well above the 0.9 V threshold. While this problem is most often associated with operation from very small
batteries or batteries that are near the end of their useful life, it can also occur when using bench power
supplies that have a slow transient response; the supply’s display may indicate a voltage above 0.9 V, but
the minimum voltage on the VBAT pin may be lower. A similar problem can occur at the output of the dc-dc
converter: using the default low current limit setting (125 mA) can trigger V
Supply Monitor resets if there
DD
is a high transient load current, particularly if the programmed output voltage is at or near 1.8 V.
16.3. Pulse Skipping Mode
The dc-dc converter allows the user to set the minimum pulse width such that if the duty cycle needs to
decrease below a certain width in order to maintain regulation, an entire "clock pulse" will be skipped.
Pulse skipping can provide substantial power savings, particularly at low values of load current. The con-
verter will continue to maintain a minimum output voltage at its programmed value when pulse skipping is
employed, though the output voltage ripple can be higher. Another consideration is that the dc-dc will oper-
ate with pulse-frequency modulation rather than pulse-width modulation, which makes the switching fre-
quency spectrum less predictable; this could be an issue if the dc-dc converter is used to power a radio.
Figure 4.5 and Figure 4.6 on page 53 and 54 show the effect of pulse skipping on power consumption.
16.4. Enabling the DC-DC Converter
On power-on reset, the state of the DCEN pin is sampled to determine if the device will power up in one-
cell or two-cell mode. In two-cell mode, the dc-dc converter always remains disabled. In one-cell mode, the
dc-dc converter remains disabled in Sleep Mode, and enabled in all other power modes. See Section
“14. Power Management” on page 157 for complete details on available power modes.
The dc-dc converter is enabled (one-cell mode) in hardware by placing a 0.68 µH inductor between DCEN
and VBAT. The dc-dc converter is disabled (two-cell mode) by shorting DCEN directly to GND. The DCEN
pin should never be left floating. The device can only switch between one-cell and two-cell mode during a
power-on reset. See Section “18. Reset Sources” on page 185 for more information regarding reset behav-
ior.
Figure 16.2 shows the two dc-dc converter configuration options.
176
Rev. 1.0