SI1011-A-GM Silicon Laboratories Inc, SI1011-A-GM Datasheet - Page 236

• Manufacturer Part Number: SI1011-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1011-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1872-5

Si1010/1/2/3/4/5
SFR Definition 21.15. P1MDIN: Port1 Input Mode
SFR Page = 0x0; SFR Address = 0xF2
SFR Definition 21.16. P1MDOUT: Port1 Output Mode
SFR Page = 0x0; SFR Address = 0xA5
236
Note: P1.0, P1.1, P1.2, and P1.3 are internally connected to the EZRadioPRO peripheral.
Note: P1.0, P1.1, P1.2, and P1.3 are internally connected to the EZRadioPRO peripheral.
Name
Reset
Name
Reset
Type
Bit
6:0
Type
Bit
6:0
7
7
Bit
Bit
P1MDOUT[6:0] Output Configuration Bits for P1.6–P1.0 (respectively).
P1MDIN[6:0] Analog Configuration Bits for P1.6–P1.0 (respectively).
Unused
Name
Unused
Name
7
1
7
0
Read =0b; Write = Don’t Care.
Port pins configured for analog mode have their weak pullup and digital receiver
disabled. The digital driver is not explicitly disabled.
0: Corresponding P1.n pin is configured for analog mode.
1: Corresponding P1.n pin is not configured for analog mode.
Read =0b; Write = Don’t Care.
These bits control the digital driver even when the corresponding bit in register
P1MDIN is logic 0.
0: Corresponding P1.n Output is open-drain.
1: Corresponding P1.n Output is push-pull.
6
1
6
0
5
1
5
0
Rev. 1.0
4
1
4
0
P1MDOUT[6:0]
P1MDIN[6:0]
Function
Function
R/W
R/W
3
1
3
0
2
1
2
0
1
1
1
0
0
1
0
0