SI1011-A-GM Silicon Laboratories Inc, SI1011-A-GM Datasheet - Page 364

• Manufacturer Part Number: SI1011-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1011-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1872-5

Si1010/1/2/3/4/5
28.3.1. Edge-triggered Capture Mode
In this mode, a valid transition on the CEXn pin causes the PCA to capture the value of the PCA
counter/timer and load it into the corresponding module's 16-bit capture/compare register (PCA0CPLn and
PCA0CPHn). The CAPPn and CAPNn bits in the PCA0CPMn register are used to select the type of
transition that triggers the capture: low-to-high transition (positive edge), high-to-low transition (negative
edge), or either transition (positive or negative edge). When a capture occurs, the Capture/Compare Flag
(CCFn) in PCA0CN is set to logic 1. An interrupt request is generated if the CCFn interrupt for that module
is enabled. The CCFn bit is not automatically cleared by hardware when the CPU vectors to the interrupt
service routine, and must be cleared by software. If both CAPPn and CAPNn bits are set to logic 1, then
the state of the Port pin associated with CEXn can be read directly to determine whether a rising-edge or
falling-edge caused the capture.
364
Operational Mode
Bit Number
Capture triggered by positive edge on CEXn
Capture triggered by negative edge on CEXn
Capture triggered by any transition on CEXn
Software Timer
High-Speed Output
Frequency Output
8-Bit Pulse Width Modulator (Note 7)
9-Bit Pulse Width Modulator (Note 7)
10-Bit Pulse Width Modulator (Note 7)
11-Bit Pulse Width Modulator (Note 7)
16-Bit Pulse Width Modulator
Notes:
Table 28.2. PCA0CPM and PCA0PWM Bit Settings for PCA Capture/Compare Modules
1. X = Don’t Care (no functional difference for individual module if 1 or 0).
2. A = Enable interrupts for this module (PCA interrupt triggered on CCFn set to 1).
3. B = Enable 8th, 9th, 10th or 11th bit overflow interrupt (Depends on setting of CLSEL[1:0]).
4. C = When set to 0, the digital comparator is off. For high speed and frequency output modes, the
5. D = Selects whether the Capture/Compare register (0) or the Auto-Reload register (1) for the associated
6. E = When set, a match event will cause the CCFn flag for the associated channel to be set.
7. All modules set to 8, 9, 10 or 11-bit PWM mode use the same cycle length setting.
associated pin will not toggle. In any of the PWM modes, this generates a 0% duty cycle (output = 0).
channel is accessed via addresses PCA0CPHn and PCA0CPLn.
Rev. 1.0
PCA0CPMn
7 6 5 4 3 2 1 0 7 6 5 4-2
X X 1 0 0 0 0 A 0 X B XXX XX
X X 0 1 0 0 0 A 0 X B XXX XX
X X 1 1 0 0 0 A 0 X B XXX XX
X C 0 0 1 0 0 A 0 X B XXX XX
X C 0 0 1 1 0 A 0 X B XXX XX
X C 0 0 0 1 1 A 0 X B XXX XX
0 C 0 0 E 0 1 A 0 X B XXX 00
0 C 0 0 E 0 1 A D X B XXX 01
0 C 0 0 E 0 1 A D X B XXX 10
0 C 0 0 E 0 1 A D X B XXX 11
1 C 0 0 E 0 1 A 0 X B XXX XX
PCA0PWM
1–0