SI1011-A-GM Silicon Laboratories Inc, SI1011-A-GM Datasheet - Page 228

• Manufacturer Part Number: SI1011-A-GM
• Description: IC TXRX MCU + EZRADIOPRO
• Manufacturer: Silicon Laboratories Inc

Specifications of SI1011-A-GM

• Package / Case: 42-QFN
• Frequency: 240MHz ~ 960MHz
• Data Rate - Maximum: 256kbps
• Modulation Or Protocol: FSK, GFSK, OOK
• Applications: General Purpose
• Power - Output: 20dBm
• Sensitivity: -121dBm
• Voltage - Supply: 1.8 V ~ 3.6 V
• Current - Receiving: 18.5mA
• Current - Transmitting: 85mA
• Data Interface: PCB, Surface Mount
• Memory Size: 8kB Flash, 768B RAM
• Antenna Connector: PCB, Surface Mount
• Number Of Receivers: 1
• Number Of Transmitters: 1
• Wireless Frequency: 240 MHz to 960 MHz
• Interface Type: UART, SMBus, SPI, PCA
• Output Power: 20 dBm
• Operating Supply Voltage: 0.9 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Maximum Supply Current: 4 mA
• Minimum Operating Temperature: - 40 C
• Modulation: FSK, GFSK, OOK
• Protocol Supported: C2, SMBus
• Core: 8051
• Program Memory Type: Flash
• Program Memory Size: 8 KB
• Data Ram Size: 768 B
• Supply Current (max): 4 mA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Operating Temperature: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1872-5

Si1010/1/2/3/4/5
SFR Definition 21.3. XBR2: Port I/O Crossbar Register 2
SFR Page = 0x0; SFR Address = 0xE3
21.4. Port Match
Port match functionality allows system events to be triggered by a logic value change on P0 or P1. A soft-
ware controlled value stored in the PnMAT registers specifies the expected or normal logic values of P0
and P1. A Port mismatch event occurs if the logic levels of the Port’s input pins no longer match the soft-
ware controlled value. This allows Software to be notified if a certain change or pattern occurs on P0 or P1
input pins regardless of the XBRn settings.
The PnMASK registers can be used to individually select which P0 and P1 pins should be compared
against the PnMAT registers. A Port mismatch event is generated if (P0 & P0MASK) does not equal
(PnMAT & P0MASK) or if (P1 & P1MASK) does not equal (PnMAT & P1MASK).
A Port mismatch event may be used to generate an interrupt or wake the device from a low power mode.
See Section “12. Interrupt Handler” on page 134 and Section “14. Power Management” on page 157 for
more details on interrupt and wake-up sources.
228
Note: The Crossbar must be enabled (XBARE = 1) to use any Port pin as a digital output.
Name
Reset
Type
5:0
Bit
Bit
7
6
WEAKPUD
WEAKPUD Port I/O Weak Pullup Disable.
Unused
XBARE
Name
R/W
7
0
0: Weak Pullups enabled (except for Port I/O pins configured for analog mode).
Crossbar Enable.
0: Crossbar disabled.
1: Crossbar enabled.
Read = 000000b; Write = Don’t Care.
XBARE
R/W
6
0
R/W
5
0
Rev. 1.0
R/W
4
0
Function
R/W
3
0
R/W
2
0
R/W
1
0
R/W
0
0