PIC18F65K90T-I/MR Microchip Technology, PIC18F65K90T-I/MR Datasheet - Page 45

• Manufacturer Part Number: PIC18F65K90T-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90T-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

REGISTER 3-3:
3.3
Essentially, PIC18F87K90 family devices have these
independent clock sources:
• Primary oscillators
• Secondary oscillators
• Internal oscillator
The primary oscillators can be thought of as the main
device oscillators. These are any external oscillators
connected to the OSC1 and OSC2 pins, and include
the External Crystal and Resonator modes and the
External Clock modes. If selected by the OSC<3:0>
Configuration bits (CONFIG1H<3:0>), the internal
oscillator block may be considered a primary oscillator.
The internal oscillator block can be one of the following:
• 31 kHz LF-INTRC source
• 31 kHz to 500 kHz MF-INTOSC source
• 31 kHz to 16 MHz HF-INTOSC source
The particular mode is defined by the OSC
Configuration bits. The details of these modes are
covered in
The secondary oscillators are external clock
sources that are not connected to the OSC1 or OSC2
pin. These sources may continue to operate, even
after the controller is placed in a power-managed
 2009-2011 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5-0
INTSRC
R/W-0
Clock Sources and
Oscillator Switching
Section 3.4 “External Oscillator
INTSRC: Internal Oscillator Low-Frequency Source Select bit
1 = 31.25 kHz device clock is derived from 16 MHz INTOSC source (divide-by-512 enabled, HF-INTOSC)
0 = 31 kHz device clock is derived from INTRC 31 kHz oscillator (LF-INTOSC)
PLLEN: Frequency Multiplier PLL Enable bit
1 = PLL is enabled
0 = PLL is disabled
TUN<5:0>: Fast RC Oscillator (INTOSC) Frequency Tuning bits
011111 = Maximum frequency
•
•
000001
000000 = Center frequency. Fast RC oscillator is running at the calibrated frequency.
111111
•
•
100000 = Minimum frequency
PLLEN
R/W-0
OSCTUNE: OSCILLATOR TUNING REGISTER
W = Writable bit
‘1’ = Bit is set
R/W-0
TUN5
Modes”.
R/W-0
TUN4
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
PIC18F87K90 FAMILY
R/W-0
TUN3
mode. PIC18F87K90 family devices offer the SOSC
(Timer1/3/5/7) oscillator as a secondary oscillator
source. This oscillator, in all power-managed modes, is
often the time base for functions, such as a Real-Time
Clock (RTC).
The SOSCEN bit in the corresponding timer should be
set
SOSCEL<1:0> bits (CONFIG1L<4:3>) decide the
SOSC mode of operation:
• 11 = High-power SOSC circuit
• 10 = Digital (SCLKI) mode
• 01 = Low-power SOSC circuit
In addition to being a primary clock source in some
circumstances, the internal oscillator is available as a
power-managed mode clock source. The LF-INTOSC
source is also used as the clock source for several
special features, such as the WDT and Fail-Safe Clock
Monitor. The internal oscillator block is discussed in
more detail in
Block”.
The PIC18F87K90 family includes features that allow
the device clock source to be switched from the main
oscillator, chosen by device configuration, to one of the
alternate clock sources. When an alternate clock
source is enabled, various power-managed operating
modes are available.
correctly
R/W-0
TUN2
for
Section 3.6 “Internal Oscillator
the
x = Bit is unknown
R/W-0
TUN1
enabled
DS39957D-page 45
SOSC.
R/W-0
TUN0
bit 0
The