PIC18F65K90-I/MR Microchip Technology, PIC18F65K90-I/MR Datasheet - Page 304

• Manufacturer Part Number: PIC18F65K90-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

PIC18F87K90 FAMILY
21.3.1
Each MSSP module has four registers for SPI mode
operation. These are:
• MSSPx Control Register 1 (SSPxCON1)
• MSSPx Status Register (SSPxSTAT)
• Serial Receive/Transmit Buffer Register
• MSSPx Shift Register (SSPxSR) – Not directly
SSPxCON1 and SSPxSTAT are the control and status
registers in SPI mode operation. The SSPxCON1
register is readable and writable. The lower 6 bits of
the SSPxSTAT are read-only. The upper two bits of the
SSPxSTAT are read/write.
SSPxSR is the shift register used for shifting data in or
out. SSPxBUF is the buffer register to which data
bytes are written to or read from.
REGISTER 21-1:
DS39957D-page 304
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
(SSPxBUF)
accessible
R/W-0
SMP
Polarity of the clock state is set by the CKP bit (SSPxCON1<4>).
REGISTERS
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at the end of data output time
0 = Input data sampled at the middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode.
CKE: SPI Clock Select bit
1 = Transmit occurs on transition from active to Idle clock state
0 = Transmit occurs on transition from Idle to active clock state
D/A: Data/Address bit
Used in I
P: Stop bit
Used in I
S: Start bit
Used in I
R/W: Read/Write Information bit
Used in I
UA: Update Address bit
Used in I
BF: Buffer Full Status bit (Receive mode only)
1 = Receive complete, SSPxBUF is full
0 = Receive not complete, SSPxBUF is empty
CKE
R/W-0
SSPxSTAT: MSSPx STATUS REGISTER (SPI MODE)
(1)
2
2
2
2
2
C™ mode only.
C mode only. This bit is cleared when the MSSPx module is disabled; SSPEN is cleared.
C mode only.
C mode only.
C mode only.
W = Writable bit
‘1’ = Bit is set
R-0
D/A
(1)
R-0
P
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
In receive operations, SSPxSR and SSPxBUF
together create a double-buffered receiver. When
SSPxSR receives a complete byte, it is transferred to
SSPxBUF and the SSPxIF interrupt is set.
During
double-buffered. A write to SSPxBUF will write to both
SSPxBUF and SSPxSR.
R-0
S
Note:
transmission,
The SSPxBUF register cannot be used
with read-modify-write instructions, such
as BCF, COMF, etc.
To avoid lost data in Master mode, a read of
the SSPxBUF must be performed to clear the
Buffer Full (BF) detect bit (SSPxSTAT<0>)
between each transmission.
R/W
R-0
 2009-2011 Microchip Technology Inc.
x = Bit is unknown
the
R-0
UA
SSPxBUF
R-0
BF
is
bit 0
not