AMD-766AC AMD [Advanced Micro Devices], AMD-766AC Datasheet - Page 64

• Manufacturer Part Number: AMD-766AC
• Description: Peripheral Bus Controller
• Manufacturer: AMD [Advanced Micro Devices]

23167B – March 2001
TTH_RATIO. Thermal throttling duty cycle. These specify the duty cycle of the STPCLK# signal to the processor
when the system is in thermal throttling mode (initiated by the THERM# pin when enabled by TTH_EN). The field
is encoded as follows:
TTH_EN. Thermal throttling enable. 1=When THERM# is asserted, thermal throttling (duty cycle specified by
TTH_RATIO) is enabled. Thermal throttling has priority over normal throttling (see PM10); however, it is disabled
if the system is in C2, C3, POS, STR, STD, or SOFF. 0=Thermal throttling disabled.
TTHLOCK. Thermal throttling lock. Write 1 only. 1=Writes to TTH_EN and TTH_RATIO are disabled. Once
set, this bit cannot be cleared by software. It is cleared by PCIRST#. Note: TTH_EN and TTH_RATIO are allowed
to change during the write command that sets TTHLOCK high.
APIC_POSEN. APIC interrupt message bus PICCLK enable during POS state. 1=PICCLK continues operation
during the POS state. 0=PICCLK is driven low after the stop-grant cycle while going into the POS suspend state.
C3A54: PCI IRQ Edge-Or-Level Select Register
Configuration space; function 3; offset: 54h. Default: 00h. Read-write.
7:4
Reserved
EDGEPI[D,C,B,A]. Edge triggered interrupt selects for PCI interrupts. Each of these controls the corresponding
PCI interrupt pin, PIRQ[D,C,B,A]#, polarity in the interrupt routing logic (see section 4.3.4.1 for details). 0=The
PIRQ[D,C,B,A]# signals are assumed to be active low and level triggered. 1=The signals are assumed to be active
low and edge triggered such that the falling edge of the external signals results in rising edges to the PIC. Note:
When these bits are high, the corresponding serial IRQ PCI interrupts are disabled.
C3A56: PCI IRQ Routing Register
Configuration space; function 3; offset: 57-56h. Default: 0000h. Read-write.
15:12
PIRQD# Select
PIRQ[D,C,B,A]# Selects. These map the PCI IRQ pins to the internal ISA-bus-compatible interrupt controller (see
section 4.3.4.1 for details). The fields are encoded as follows:
C3A58: System Management IO Space Pointer
Configuration space; function 3; offset: 5B-58h. Default: 0000_DD01h.
31:16
Reserved
PMBASE. Read-write. Specifies PCI address bits[15:8] of the 256-byte block of IO-mapped registers used for
system management (address space PMxx). Access to this address space is enabled by C3A41[PMIOEN].
PMBLSB. Read only. These bits are fixed in their default state.
PIRQ[D,C,B,A]# Selects
0h
1h
2h
3h
4h
5h
6h
7h
RATIO bits
000b
001b
010b
011b
Description
Reserved.
87.5% STPCLK# active.
75.0% STPCLK# active.
62.5% STPCLK# active.
11:8
PIRQC# Select
Selected IRQ
None
IRQ1
Reserved
IRQ3
IRQ4
IRQ5
IRQ6
IRQ7
Preliminary Information
RATIO bits
3
EDGEPID
7:4
PIRQB# Select
15:8
PMBASE
PIRQ[D,C,B,A]# Selects
8h
9h
Ah
Bh
Ch
Dh
Eh
Fh
100b
101b
110b
111b
AMD-766
Description
50.0% STPCLK# active.
37.5% STPCLK# active.
25.0% STPCLK# active.
12.5% STPCLK# active.
2
EDGEPIC
TM
Peripheral Bus Controller Data Sheet
1
EDGEPIB
3:0
PIRQA# Select
7:0
PMBLSB
Selected IRQ
Reserved
IRQ9
IRQ10
IRQ11
IRQ12
Reserved
IRQ14
IRQ15
0
EDGEPIA
64