PIC16F785-I/SO Microchip Technology, PIC16F785-I/SO Datasheet - Page 37

• Manufacturer Part Number: PIC16F785-I/SO
• Description: IC PIC MCU FLASH 2KX14 20SOIC
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F785-I/SO

• Program Memory Type: FLASH
• Program Memory Size: 3.5KB (2K x 14)
• Package / Case: 20-SOIC (7.5mm Width)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 17
• Eeprom Size: 256 x 8
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DV164120, DM163029
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT20SO1-1 - SOCKET TRANS ICE 20DIP TO 20SOICXLT18SO-1 - SOCKET TRANSITION 18SOIC 300MILAC162060 - HEADER INTRFC MPLAB ICD2 20PINAC164039 - MODULE SKT PROMATE II 20DIP/SOIC
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.2.2
Each of the PORTA pins is individually configurable as
an interrupt-on-change pin. Control bits IOCAx enable
or disable the interrupt function for each pin. Refer to
Register 4-4. The interrupt-on-change is disabled on a
Power-on Reset.
For enabled interrupt-on-change pins, the values are
compared with the old value latched on the last read of
PORTA. The ‘mismatch’ outputs of the last read are
OR'd together to set, the PORTA Change Interrupt flag
bit (RAIF) in the INTCON register (Register 2-3).
REGISTER 4-4:
 2004 Microchip Technology Inc.
bit 7-6
bit 5-0
INTERRUPT-ON-CHANGE
IOCA — INTERRUPT-ON-CHANGE PORTA REGISTER (ADDRESS: 96h)
bit 7
Unimplemented: Read as ‘0’
IOCA<5:0>: Interrupt-on-change PORTA Control bits
1 = Interrupt-on-change enabled
0 = Interrupt-on-change disabled
Legend:
R = Readable bit
- n = Value at POR
Note 1: Global interrupt enable (GIE) must be enabled for individual interrupts to be
U-0
—
2: IOCA<5:4> always reads ‘1’ in XT, HS and LP OSC modes.
recognized.
U-0
—
IOCA5
R/W-0
Preliminary
W = Writable bit
‘1’ = Bit is set
IOCA4
R/W-0
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, clears the
interrupt by:
a)
b)
A mismatch condition will continue to set flag bit RAIF.
Reading PORTA will end the mismatch condition and
allow flag bit RAIF to be cleared. The latch holding the
last read value is neither affected by an MCLR nor BOR
Reset. After these resets, the RAIF flag will continue to
be set if a mismatch is present.
Note:
Any read or write of PORTA. This will end the
mismatch condition, then,
Clear the flag bit RAIF.
IOCA3
R/W-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the RAIF
interrupt flag may not get set.
(2)
IOCA2
R/W-0
PIC16F785
x = Bit is unknown
IOCA1
R/W-0
DS41249A-page 35
(1)
IOCA0
R/W-0
bit 0