MC9S12DT256MPVE Freescale Semiconductor, MC9S12DT256MPVE Datasheet - Page 509

• Manufacturer Part Number: MC9S12DT256MPVE
• Description: IC MCU 256K FLASH 25MHZ 112-LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12DT256MPVE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: CAN, I²C, SCI, SPI
• Peripherals: PWM, WDT
• Number Of I /o: 91
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 2.35 V ~ 5.25 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 112-LQFP
• Processor Series: S12D
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 12 KB
• Interface Type: CAN/I2C/SCI/SPI
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 91
• Number Of Timers: 1
• Operating Supply Voltage: 5 V to 2.5 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: M68KIT912DP256
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 2 (8-ch x 10-bit)
• No. Of I/o's: 91
• Eeprom Memory Size: 4KB
• Ram Memory Size: 12KB
• Cpu Speed: 25MHz
• No. Of Timers: 1
• No. Of Pwm Channels: 8
• Digital Ic Case Style: LQFP
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.4.6.5.2
Figure 11-29
instead of RT16 but is still sampled at RT8, RT9, and RT10.
For an 8-bit data character, it takes the receiver 9 bit times x 16 RTr cycles + 10 RTr cycles = 154 RTr cycles
to finish data sampling of the stop bit.
With the misaligned character shown in
the count of the transmitting device is 10 bit times x 16 RTt cycles = 160 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a fast 8-bit
character with no errors is:
For a 9-bit data character, it takes the receiver 10 bit times x 16 RTr cycles + 10 RTr cycles = 170 RTr cycles
to finish data sampling of the stop bit.
With the misaligned character shown in
the count of the transmitting device is 11 bit times x 16 RTt cycles = 176 RTt cycles.
The maximum percent difference between the receiver count and the transmitter count of a fast 9-bit
character with no errors is:
11.4.6.6
To enable the SCI to ignore transmissions intended only for other receivers in multiple-receiver systems,
the receiver can be put into a standby state. Setting the receiver wakeup bit, RWU, in SCI control register 2
(SCICR2) puts the receiver into standby state during which receiver interrupts are disabled.The SCI will
still load the receive data into the SCIDRH/L registers, but it will not set the RDRF flag.
The transmitting device can address messages to selected receivers by including addressing information in
the initial frame or frames of each message.
The WAKE bit in SCI control register 1 (SCICR1) determines how the SCI is brought out of the standby
state to process an incoming message. The WAKE bit enables either idle line wakeup or address mark
wakeup.
Freescale Semiconductor
((160 – 154) / 160) x 100 = 3.75%
((176 – 170) /176) x 100 = 3.40%
Receiver Wakeup
shows how much a fast received frame can be misaligned. The fast stop bit ends at RT10
Fast Data Tolerance
RT Clock
Receiver
MC9S12XDP512 Data Sheet, Rev. 2.21
Figure
Figure
Figure 11-29. Fast Data
Stop
11-29, the receiver counts 154 RTr cycles at the point when
11-29, the receiver counts 170 RTr cycles at the point when
Samples
Data
Chapter 11 Serial Communication Interface (S12SCIV5)
Idle or Next Frame
509