ADUC7032BSTZ-8V-RL Analog Devices Inc, ADUC7032BSTZ-8V-RL Datasheet - Page 57
![IC BATTERY SENSOR PREC 48-LQFP](/photos/6/59/65923/505-48-lqfp_sml.jpg)
ADUC7032BSTZ-8V-RL
Manufacturer Part Number
ADUC7032BSTZ-8V-RL
Description
IC BATTERY SENSOR PREC 48-LQFP
Manufacturer
Analog Devices Inc
Series
MicroConverter® ADuC7xxxr
Datasheet
1.ADUC7032BSTZ-8V-RL.pdf
(128 pages)
Specifications of ADUC7032BSTZ-8V-RL
Core Processor
ARM7
Core Size
16/32-Bit
Speed
20.48MHz
Connectivity
LIN, SPI, UART/USART
Peripherals
POR, PSM, Temp Sensor, WDT
Number Of I /o
9
Program Memory Size
96KB (96K x 8)
Program Memory Type
FLASH
Ram Size
6K x 8
Voltage - Supply (vcc/vdd)
3.5 V ~ 18 V
Data Converters
A/D 2x16b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 105°C
Package / Case
48-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Eeprom Size
-
Other names
ADUC7032BSTZ-8V-RLCT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ADUC7032BSTZ-8V-RL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Preliminary Technical Data
ADC Configuration Register :
Name :
Address :
Default Value :
Access :
Function :
Bit
7
6, 5
4, 3
2
1
0
Description
Analog Ground Switch Enable
This bit is set to ‘1’ by user software to connect the external ‘GND_SW’ pin (pin#15) to an internal analog ground reference
point. This bit can be used to connect and disconnect external circuits and components to ground under program
control and thereby minimize dc current consumption when the external circuit or component is not being used.
This bit is used in conjunction with ADCMDE[6] to select a 20KΩ resistor to ground.
Current Channel (32-bit) Accumulator Enable
0, 0
0, 1
1, 0
1, 1
Current Channel ADC Comparator Enable
0, 0
0, 1
1, 0
1, 1
Current Channel ADC OverRange Enable
Set by user to enable a ‘coarse’ comparator on the Current Channel ADC. If the current reading is grossly (>30% approx.)
over-ranged for the active gain setting, then the over range bit in the ADCSTA MMR is set. The current must be outside
this range for greater than 125usecs for the flag to be set.
This feature should not be used in ADC Low Power Mode
ADC FIFO Enable
This bit is set to 1 by user code to enable ADC FIFO on Current and Voltage ADC Channels. The FIFO function allows up to
32 current and voltage ADC results to be stored in an on-chip FIFO. The current status of the FIFO is reflected by 3 bits in
the ADCSTA register.
If more than 32 results are stored in the FIFO, the contents of the FIFO may be corrupted.
Current Channel ADC, Result Counter Enable
Set by user to enable the result count mode. In this mode an I-ADC interrupt will only be generated when
ADC0RCV=ADC0RCL. This allows the I-ADC to continuously monitor current but only interrupt the MCU core after a
defined number of conversions. It should be noted that unless the ADC FIFO is enabled (ADCCNG[1]=1), only the last
conversion value will be available (intermediate I-ADC conversion results are not stored) when the ADC counter interrupt
occurs. The Voltage and Temperature ADCs will also continue to convert if enabled but again only the last conversion
result will be available (intermediate V/T-ADC conversion results are not stored) when the ADC counter interrupt occurs
ADCCFG
0xFFFF051C
0x00
Read/Write
The 8-bit ADC Configuration MMR controls extended functionality related to the on-chip ADCs.
Accumulator Disabled and reset to 0
Accumulator Active
Accumulator Active
Accumulator and Accumulator Comparator Enabled
Comparator Active, Interrupt asserted if absolute value of I-ADC conversion result |I| >= ADC0TH
Comparator-Count Mode Active, Interrupt asserted if absolute value of an I-ADC conversion result |I| >=
Comparator-Count Mode Active, Interrupt asserted if absolute value of an I-ADC conversion result |I| >=
Positive current values are added to accumulator total, accumulator can overflow if allowed run for > 65535
conversions
Negative current values are subtracted from accumulator total, accumulator is clamped to a
minimum value of 0
Positive current values are added to accumulator total, accumulator can overflow if allowed run for > 65535
conversions
The absolute values of Negative current are subtracted from accumulator total, accumulator in this mode will
This mode is the same as Mode |1,0|, but with the Accumulator Comparator enabled.
Comparator Disabled
ADC0TH for #ADC0TCL conversions. A conversion value |I| < ADC0TH will reset the threshold counter value
(ADC0THV) to 0
ADC0TH for #ADC0TCL conversions. A conversion value |I| < ADC0TH will decrement the threshold counter
value (ADC0THV) towards 0.
continue to accumulate negatively, below 0
Table 30: ADCCFG MMR Bit Designations
Rev. PrD | Page 57 of 128
ADuC7032