EP9312-CB Cirrus Logic Inc, EP9312-CB Datasheet - Page 313

• Manufacturer Part Number: EP9312-CB
• Description: System-on-Chip Processor
• Manufacturer: Cirrus Logic Inc
• Series: EP9r

Specifications of EP9312-CB

• Peak Reflow Compatible (260 C): No
• A/d Converter: 12 Bits
• Leaded Process Compatible: No
• No. Of I/o Pins: 65
• Package / Case: 352-BGA
• Core Processor: ARM9
• Core Size: 16/32-Bit
• Speed: 200MHz
• Connectivity: EBI/EMI, EIDE, Ethernet, I²C, IrDA, Keypad/Touchscreen, SPI, UART/USART, USB
• Peripherals: AC'97, DMA, I&sup2:S, LCD, LED, MaverickKey, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: ROMless
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 8x12b
• Oscillator Type: External
• Operating Temperature: 0°C ~ 70°C
• Processor Series: EP93xx
• Core: ARM920T
• Data Bus Width: 32 bit
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -
• Program Memory Size: -
• Lead Free Status / Rohs Status: No
• Other names: 598-1257

DS785UM1
9.1.4.10 Rx Missed and Tx Collision Counters
9.1.4.11 Accessing the MII
To comply with the standard, pause frames should only be sent on full duplex links. The MAC
does not enforce this, it is left to the driver. If a pause frame is sent on a half duplex link, it is
subject to the normal half duplex collisions rules and retry attempts.
The format of a transmit pause frame is:
Bytes 1-6 - Destination address - this is the last Individual address (Address Filter Pointer =
6)
Bytes 7-12 - Source address - this is the first Individual address (Address Filter Pointer = 0)
Bytes 13-14 - Type field - this is defined in the Flow Control Format register
Bytes 15-16 - Opcode - set to 0x0001
Bytes 17-18 - Pause time - this is defined in the Flow Control Format register
Once the Host sets the Send Pause bit in TXCtl, it will remain set until the pause frame starts
transmission. Then the Send Pause clears and the Pause Busy bit is set and remains set
until the transmission is complete. No end of frame status is generated for pause frames.
There are three counters that help the software in recording events, transmit collisions,
receive missed frames, and receive runt frames. All three counters operate in similar ways.
When the appropriate events occur the counters are incremented. They are cleared following
a read of the count value. If a count is incremented such that the MSB is set, the
corresponding status bit in the Interrupt Status Register is set. An interrupt is generated at
this time if the corresponding enable bit is set in the Interrupt Enable Register. Once the
count is incremented to an all ones condition it will not be incremented further, it will remain in
this state until reset by a read operation.
This section describes the proper method to access the MII. It includes how to read/write
PHY registers, how to have the PHY perform auto-negotiation, and how to startup the PHY.
The bits MDCDIV in register SelfCtl are used to control the PHY's clock divisor. The default
value is 0x07, so the MDC clock frequency is HCLK divided by 8. This default value is correct
for most PHYs. However, to be safe, check the PHY's data sheet to make sure that this clock
frequency is correct.
The bit PSPRS in register SelfCtl is used to disable/enable Preamble Suppress for data
passed from the MAC to the PHY through the MDIO. If bit PSPRS is set, the preamble is
suppressed. In this case, the MAC won't prepend 32 bits of “1” to the data written to the PHY.
Since the MAC automatically prepends the preamble to data when in transmission mode, bit
PSPRS must be set while the MAC is transmitting frames. Otherwise, two preambles will be
prepended and cause a transmission failure. The default value of “1” is appropriate for
transmitting frames.
The MAC won't automatically prepend a preamble when not in transmission mode.
Therefore, if the MAC wants to read/write PHY registers, bit PSPRS may be cleared since
Copyright 2007 Cirrus Logic
1/10/100 Mbps Ethernet LAN Controller
EP93xx User’s Guide
9-11
9