MT29F2G08ABAEAH4-IT:E Micron Technology Inc, MT29F2G08ABAEAH4-IT:E Datasheet - Page 71

• Manufacturer Part Number: MT29F2G08ABAEAH4-IT:E
• Description: IC FLASH 2G 3.3V SLC 63VFBGA
• Manufacturer: Micron Technology Inc

Specifications of MT29F2G08ABAEAH4-IT:E

• Format - Memory: FLASH
• Memory Type: FLASH - Nand
• Memory Size: 2G (256M x 8)
• Interface: Parallel
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 63-VFBGA
• Cell Type: NAND
• Density: 2Gb
• Interface Type: Parallel
• Address Bus: 28b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: VFBGA
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 256M
• Supply Current: 35mA
• Mounting: Surface Mount
• Pin Count: 63
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Speed: -
• Lead Free Status / Rohs Status: Compliant

ERASE BLOCK TWO-PLANE (60h-D1h)
Figure 47: ERASE BLOCK TWO-PLANE (60h–D1h) Operation
PDF: 09005aef83b83f42
m69a_2gb_nand.pdf – Rev. H 09/10 EN
The ERASE BLOCK TWO-PLANE (60h-D1h) command queues a block in the specified
plane to be erased in the NAND Flash array. This command can be issued one or more
times. Each time a new plane address is specified, that plane is also queued for a block
to be erased. To specify the final block to be erased and to begin the ERASE operation
for all previously queued planes, issue the ERASE BLOCK (60h-D0h) command. This
command is accepted by the die (LUN) when it is ready (RDY = 1, ARDY = 1).
To queue a block to be erased, write 60h to the command register, then write three ad-
dress cycles containing the row address; the page address is ignored. Conclude by
writing D1h to the command register. The selected die (LUN) will go busy (RDY = 0,
ARDY = 0) for
To determine the progress of
alternatively, the status operations (70h, 78h) can be used. When the LUN's status
shows that it is ready (RDY = 1, ARDY = 1), additional ERASE BLOCK TWO-PLANE (60h-
D1h) commands can be issued to queue additional planes for erase. Alternatively, the
ERASE BLOCK (60h-D0h) command can be issued to erase all of the queued blocks.
For two-plane addressing requirements for the ERASE BLOCK TWO-PLANE (60h-D1h)
and ERASE BLOCK (60h-D0h) commands, see Two-Plane Operations.
Cycle type
I/O[7:0]
RDY
Command
t
DBSY.
60h
Address
R1
71
t
DBSY, the host can monitor the target's R/B# signal, or
Address
R2
Micron Technology, Inc. reserves the right to change products or specifications without notice.
Address
2Gb: x8, x16 NAND Flash Memory
R3
Command
D1h
t WB
t DBSY
© 2009 Micron Technology, Inc. All rights reserved.
Erase Operations
Command
60h
Address
...