RG82845 S L5YQ Intel, RG82845 S L5YQ Datasheet - Page 21

• Manufacturer Part Number: RG82845 S L5YQ
• Manufacturer: Intel

Specifications of RG82845 S L5YQ

• Lead Free Status / RoHS Status: Not Compliant

2.1
Intel
®
82845 MCH for SDR Datasheet
R
System Bus Signals
ADS#
BNR#
BPRI#
BR0#
CPURST#
DBSY#
DEFER#
DBI[3:0]#
DRDY#
HA[31:3]#
HADSTB[1:0]#
Signal Name
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
AGTL+
Type
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
O
O
Address Strobe: The system bus owner asserts ADS# to indicate the first
of two cycles of a request phase.
Block Next Request: BNR# is used to block the current request bus
owner from issuing a new request. This signal dynamically controls the
system bus pipeline depth.
Bus Priority Request: The MCH is the only Priority Agent on the system
bus. It asserts this signal to obtain the ownership of the address bus. This
signal has priority over symmetric bus requests and will cause the current
symmetric owner to stop issuing new transactions unless the HLOCK#
signal was asserted.
Bus Request 0#: The MCH pulls the processor bus BR0# signal low
during CPURST#. The signal is sampled by the processor on the active-to-
inactive transition of CPURST#. The minimum setup time for this signal is
4 BCLKs. The minimum hold time is 2 BCLKs and the maximum hold time
is 20 BCLKs. BR0# should be three-stated after the hold time requirement
has been satisfied.
Processor Reset: The CPURST# pin is an output from the MCH. The
MCH asserts CPURST# while RSTIN# (PCIRST# from the ICH2) is
asserted and for approximately 1 ms after RSTIN# is deasserted. The
CPURST# allows the processor to begin execution in a known state.
Data Bus Busy: DBSY# is used by the data bus owner to hold the data
bus for transfers requiring more than one cycle.
Defer Response: This signal, when asserted, indicates that the MCH will
terminate the transaction currently being snooped with either a deferred
response or with a retry response.
Dynamic Bus Inversion: DBI[3:0]# are driven along with the HD[63:0]#
signals. DBI[3:0]# Indicate if the associated data signals are inverted.
DBI[3:0]# are asserted such that the number of data bits driven electrically
low (low voltage) within the corresponding 16-bit group never exceeds 8.
DBI[x]#
DBI3#
DBI2#
DBI1#
DBI0#
Data Ready: Asserted for each cycle that data is transferred.
Host Address Bus: HA[31:3]# connect to the system address bus. During
processor cycles, HA[31:3]# are inputs. The MCH drives HA[31:3]# during
snoop cycles on behalf of the hub interface and AGP/Secondary PCI
initiators. HA[31:3]# are transferred at 2x rate. Note that the address is
inverted on the system bus.
Host Address Strobe: The source synchronous strobes used to transfer
HA[31:3]# and HREQ[4:0]# at the 2x transfer rate.
Strobe
HADSTB0#
HADSTB1#
HD[63:48]#
HD[47:32]#
HD[31:16]#
HD[15:0]#
HA[16:3]#, HREQ[4:0]#
HA[31:17]#
Address Bits
Data Bits
Description
Signal Description
21