UPD78F1201MC-CAB-AX Renesas Electronics America, UPD78F1201MC-CAB-AX Datasheet - Page 477

• Manufacturer Part Number: UPD78F1201MC-CAB-AX
• Description: MCU 16BIT 78K0R/LX3 30-SSOP
• Manufacturer: Renesas Electronics America
• Series: 78K0R/Ix3r

Specifications of UPD78F1201MC-CAB-AX

• Core Processor: 78K/0R
• Core Size: 16-Bit
• Speed: 40MHz
• Connectivity: 3-Wire SIO, I²C, LIN, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 21
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Remark
During
operation
Operation
stop
TAUS stop
n = 01
m = 02 to 07
The TT00 (master) and TTn (slave 1) bits are set to 1 at
the same time.
Set value of the TDR00 and TDRn registers can be
changed.
The TCR00 and TCRn registers can always be read.
Set values of the TROn and TROm bits can be
changed.
The TOEn and TOEm bits are cleared to 0 and values
are set to TOn and TOm.
To hold the TOn and TOm pin output levels
When holding the TOn and TOm pin output levels is not
necessary
The TAU0EN and TAUOPEN bits of the PER2 register
are cleared to 0.
Figure 7-77. Operation Procedure of Linked Real-Time Output Function (Type 3) (2/2)
The TT00 and TTn bits automatically return to 0
because they are trigger bits.
Clears the TOn and TOm bits to 0 after the values to
be held are set to the port register.
Switches the port mode register to input mode.
Software Operation
CHAPTER 7 INVERTER CONTROL FUNCTIONS
User’s Manual U19678EJ1V1UD
The TOn and TOm pin output levels go into Hi-Z output
state.
The counter of the master channel loads the TDR00 value
to TCR00 and counts down. When the count value reaches
TCR00 = 0000H, INTTM00 is generated. At the same time,
the value of the TDR00 register is loaded to TCR00, and
the counter starts counting down again.
At slave channel 1, the value of the TDRn register is
transferred to TCRn, triggered by TSn = 1, and the counter
starts counting down. When the counter has counted down
to 0000H, INTTMn is output and the counting operation is
stopped. After that, the above operation is repeated. The
set value of TROm of the slave channels 2 to 7 (real-time
output channel) is output from TOm at the INTTMn output
timing.
TE00, TEn = 0, and count operation stops.
The set values of TOn and TOm initialize the outputs of
TOn and TOm.
The TOn and TOm pin output levels are held by port
function.
Power-off status
TCR00 and TCRn hold count value and stops.
The TOn and TOm output is not initialized but holds
current status.
All circuits are initialized and SFR of each channel is also
initialized.
(The TOn and TOm bits are cleared to 0 and the TOn
and TOm pins are set to port mode.)
Hardware Status
475