UPD70F3737GC-UEU-AX Renesas Electronics America, UPD70F3737GC-UEU-AX Datasheet - Page 563

• Manufacturer Part Number: UPD70F3737GC-UEU-AX
• Description: MCU 32BIT V850ES/JX3-L 100-LQFP
• Manufacturer: Renesas Electronics America
• Series: V850ES/Jx3-Lr

Specifications of UPD70F3737GC-UEU-AX

• Package / Case: *
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Speed: 20MHz
• Number Of I /o: 84
• Core Processor: RISC
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Program Memory Size: 128KB (128K x 8)
• Data Converters: A/D 12x10b, D/A 2x8b
• Oscillator Type: Internal
• Peripherals: DMA, LVD, PWM, WDT
• Connectivity: CSI, EBI/EMI, I²C, UART/USART
• Core Size: 32-Bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Note Set the SPTn bit to 1 only in master mode. However, when the IICRSVn bit is 0, the SPTn bit must be
Caution When the TRCn bit = 1, the WRELn bit is set to 1 during the ninth clock and the wait
Remarks 1. The SPTn bit is 0 if it is read immediately after data setting.
Cautions concerning set timing
For master reception:
For master transmission: A stop condition cannot be generated normally during the ACK reception period. Set to
• Cannot be set to 1 at the same time as the STTn bit.
• The SPTn bit can be set to 1 only when in master mode
• When the WTIMn bit has been set to 0, if the SPTn bit is set to 1 during the wait period that follows output of
• When the SPTn bit is set to 1, setting the SPTn bit to 1 again is disabled until the setting is cleared to 0.
Condition for clearing (SPTn bit = 0)
• Cleared by loss in arbitration
• Automatically cleared after stop condition is detected
• When the LRELn bit = 1 (communication save)
• When the IICEn bit = 0 (operation stop)
• After reset
SPTn
eight clocks, note that a stop condition will be generated during the high-level period of the ninth clock.
The WTIMn bit should be changed from 0 to 1 during the wait period following output of eight clocks, and the
SPTn bit should be set to 1 during the wait period that follows output of the ninth clock.
0
1
set to 1 and a stop condition generated before the first stop condition is detected following the switch
to the operation enabled status. For details, see 17.15 Cautions.
state is canceled, after which the TRCn bit is cleared to 0 and the SDA0n line is set to
high impedance.
2. n = 0 to 2
Stop condition is not generated.
Stop condition is generated (termination of master device’s transfer).
After the SDA0n line goes to low level, either set the SCL0n line to high level or wait until the SCL0n
pin goes to high level. Next, after the rated amount of time has elapsed, the SDA0n line is changed
from low level to high level and a stop condition is generated.
Cannot be set to 1 during transfer.
Can be set to 1 only when the ACKEn bit has been set to 0 and during the wait period
after the slave has been notified of final reception.
1 during the wait period that follows output of the ninth clock.
Preliminary User’s Manual U18953EJ1V0UD
CHAPTER 17 I
Stop condition trigger
2
C BUS
Note
Condition for setting (SPTn bit = 1)
• Set by instruction
.
(4/4)
563