M30260F6AGP#D5 Renesas Electronics America, M30260F6AGP#D5 Datasheet - Page 262

• Manufacturer Part Number: M30260F6AGP#D5
• Description: IC M16C MCU FLASH 48K 48-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

R
R
M
e
E
1
. v
J
Figure 17.5.1.1. Setting and Resetting of EW0 Mode
6
Figure 17.5.1.2. Setting and Resetting of EW1 Mode
0
C
2
9
0 .
B
2 /
0
0
6
2
A
0
F
2
e
NOTES:
G
0 -
Transfer a rewrite control program to internal RAM
area
b
EW0 mode operation procedure
Jump to the rewrite control program transfered to an
internal RAM area (in the following steps, use the
rewrite control program internal RAM area)
o r
1 .
1. Select 10 MHz or below for CPU clock using the CM06 bit in the CM0 register and CM17 to 16 bits in the CM1
2. Set the FMR01 bit to “1” immediately after setting it to “0”. Do not generate an interrupt or a DMA transfer between
3. Disables the CPU rewrite mode after executing the read array command.
2
0
, 5
u
register. Also, set the PM17 bit in the PM1 register to “1” (with wait state).
setting the bit to “0” and setting it to “1”. Set the FMR01 bit in a space other than the internal flash memory. Also,
set only when the P8
Set CM0, CM1, and PM1 registers (1)
0
p
2
(
0
M
0
7
1
6
C
page 243
2 /
Single-chip mode
6
, A
NOTES:
1. Select 10 MHz or below for CPU clock using the CM06 bit in the CM0 register and CM17 to 16 bits.
2. Set the FMR01 bits to “1” immediately after setting it to “0”. Do not generate an interrupt or a DMA
3. Set the FMR11 bit to "1" immediately after setting it to "0" while the FMR01 bit is set to "1". Do not
5
M
/NMI/SD pin is “H” at the time of the NMI function selected.
in the CM1 register. Also, set the PM17 bit in the PM1 register to “1” (with wait state).
transfer between setting the bit to “0” and setting the bit to “1”. Set the FMR01 bit in a space other
than the internal flash memory. Set only when the P8
function selected.
generate an interrupt or a DMA transfer between setting the FMR11 bit to "0" and setting it to "1".
EW mode 1 operation procedure
1
f o
6
C
3
2
2 /
9
6
, B
Set the FMR01 bit to “1” (CPU rewrite mode
enabled) after writing “0”
Set the FMR11 bit to “1” (EW mode 1) after writing
“0”
M
(2, 3)
Set CM0, CM1, and PM1 registers
1
6
Execute software commands
C
(CPU rewrite mode disabled)
2 /
Set the FMR01 bit to “0”
Single-chip mode
Program in ROM
6
) T
Rewrite control program
Jump to a specified address in the flash memory
Set the FMR01 bit to “1” after writing “0”
(CPU rewrite mode enabled) (2)
Execute the Read Array command (3)
5
/NMI/SD pin is “H” at the time of the NMI
(1)
Execute software commands
(CPU rewrite mode disabled)
Write “0” to the FMR01 bit
17. Flash Memory Version