M30260F6AGP#D5 Renesas Electronics America, M30260F6AGP#D5 Datasheet - Page 336

• Manufacturer Part Number: M30260F6AGP#D5
• Description: IC M16C MCU FLASH 48K 48-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M
R
R
e
E
19.10 Programmable I/O Ports
1
. v
J
6
0
C
2
9
0 .
2 /
B
1. If a low-level signal is applied to the SD pin when the IVPCR1 bit in the TB2SC register is set to “1”
2. The input threshold voltage of pins differs between programmable input/output ports and peripheral
3. When the INV03 bit in the INVC0 register is "1"(three-phase motor control timer output enabled), an "L"
0
0
6
(three-phase output forcible cutoff by input on SD pin enabled), the P7
a high-impedance state.
functions.
Therefore, if any pin is shared by a programmable input/output port and a peripheral function and the
input level at this pin is outside the range of recommended operating conditions V
“high” nor “low”), the input level may be determined differently depending on which side—the program-
mable input/output port or the peripheral function—is currently selected.
input on the P8
Therefore, the P8
When the SD function isn't used, set PD8
2
A
0
F
2
e
G
0 -
b
•When the IVPCR1 bit in the TB2SC register is set to “1” (three-phase output forcible cutoff by input
•When the IVPCR1 bit is set to “0” (three-phase output forcible cutoff by input on SD pin
o r
1 .
2
on the SD pin enabled), the U/ U/ V/ V/ W/ W pins go to a high-impedance state.
disabled), the U/ U/ V/ V/ W/ W pins go to a normal port.
0
u
, 5
0
p
2
(
0
_____
M
0
7
1
_____
6
C
5
page 317
2 /
_______ _____
/NMI/SD pin, has the following effect:
5
6
pin can not be used as programmable I/O port when the INV03 bit is set to "1".
, A
M
__
1
f o
6
C
3
2
2 /
__
9
6
, B
M
___
1
__
_____
6
C
2 /
5
6
__
to “0” (Input) and pull the P8
) T
_____
___
2
to P7
5
_______ _____
/NMI/SD pin to “H” externally.
5
, P8
0
and P8
IH
and V
_____
19. Usage Notes
1
IL
pins go to
(neither