M30260F6AGP#D5 Renesas Electronics America, M30260F6AGP#D5 Datasheet - Page 53

• Manufacturer Part Number: M30260F6AGP#D5
• Description: IC M16C MCU FLASH 48K 48-LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#D5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

M
R
R
e
E
1
. v
J
6
0
C
2
9
5.5.2 Limitations on Exiting Stop Mode
5.5.3 Limitations on Exiting Wait Mode
0 .
2 /
B
0
0
6
2
A
0
The voltage down detection interrupt is immediately generated and the microcomputer exits stop
mode if the CM10 bit in the CM1 register is set to “1” under the conditions below.
• the VC27 bit in the VCR2 register is set to “1” (voltage down detection circuit enabled),
• the D40 bit in the D4INT register is set to “1” (voltage down detection interrupt enabled),
• the D41 bit in the D4INT register is set to “1” (voltage down detection interrupt is used to exit stop
mode), and
• the voltage applied to the VCC pin is higher than Vdet4 (the VC13 bit in the VCR1 register is “1”)
If the microcomputer is set to enter stop mode when the voltage applied to the VCC pin drops below
Vdet4 and to exit stop mode when the voltage applied rises to Vdet4 or above, set the CM10 bit to “1”
when VC13 bit is “0” (VCC < Vdet4).
The voltage down detection interrupt is immediately generated and the microcomputer exits wait
mode If WAIT instruction is executed under the conditions below.
• the CM02 bit in the CM0 register is set to “1” (stop peripheral function clock),
• the VC27 bit in the VCR2 register is set to “1” (voltage down detection circuit enabled),
• the D40 bit in the D4INT register is set to “1” (voltage down detection interrupt enabled),
• the D41 bit in the D4INT register is set to “1” (voltage down detection interrupt is used to exit wait
mode), and
• the voltage applied to the VCC pin is higher than Vdet4 (the VC13 bit in the VCR1 register is “1”)
If the microcomputer is set to enter wait mode when the voltage applied to the VCC pin drops below
Vdet4 and to exit wait mode when the voltage applied rises to Vdet4 or above, perform WAIT instruc-
tion when VC13 bit is “0” (VCC < Vdet4).
F
2
e
G
0 -
b
o r
1 .
2
0
u
, 5
0
p
2
(
0
M
0
1
7
6
C
2 /
page 34
6
, A
M
1
f o
6
C
3
2
2 /
9
6
, B
M
1
6
C
2 /
6
) T
5. Reset