EP1AGX20CF484C6N Altera, EP1AGX20CF484C6N Datasheet - Page 44

• Manufacturer Part Number: EP1AGX20CF484C6N
• Description: IC ARRIA GX FPGA 20K 484FBGA
• Manufacturer: Altera
• Series: Arria GXr

Specifications of EP1AGX20CF484C6N

• Number Of Logic Elements/cells: 21580
• Number Of Labs/clbs: 1079
• Total Ram Bits: 1229184
• Number Of I /o: 230
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Arria™ GX
• Number Of Logic Blocks/elements: 21580
• # I/os (max): 230
• Process Technology: CMOS
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 21580
• Ram Bits: 1229184
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FC-FBGA
• No. Of Macrocells: 21580
• Family Type: Arria GX
• No. Of I/o's: 230
• Operating Frequency Max: 622.08MHz
• Operating Temperature Range: 0°C To +85°C
• Logic Case Style: BGA
• No. Of Pins: 484
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 544-2395

2–38
Arithmetic Mode
Figure 2–34. ALM in Arithmetic Mode
Arria GX Device Handbook, Volume 1
Arithmetic mode is ideal for implementing adders, counters, accumulators, wide
parity functions, and comparators. An ALM in arithmetic mode uses two sets of 2
four-input LUTs along with two dedicated full adders. The dedicated adders allow
the LUTs to be available to perform pre-adder logic; therefore, each adder can add the
output of two four-input functions. The four LUTs share the dataa and datab
inputs. As shown in
carry-out from adder0 feeds to carry-in of adder1. The carry-out from adder1
drives to adder0 of the next ALM in the LAB. ALMs in arithmetic mode can drive
out registered and/or unregistered versions of the adder outputs.
While operating in arithmetic mode, the ALM can support simultaneous use of the
adder’s carry output along with combinational logic outputs. In this operation, adder
output is ignored. This usage of the adder with the combinational logic output
provides resource savings of up to 50% for functions that can use this ability. An
example of such functionality is a conditional operation, such as the one shown in
Figure
Equation 2–1.
To implement this function, the adder is used to subtract ‘Y’ from ‘X.’ If ‘X’ is less than
‘Y,’ the carry_out signal is ‘1.’ The carry_out signal is fed to an adder where it
drives out to the LAB local interconnect. It then feeds to the LAB-wide syncload
signal. When asserted, syncload selects the syncdata input. In this case, the data
‘Y’ drives the syncdata inputs to the registers. If ‘X’ is greater than or equal to ‘Y,’ the
syncload signal is deasserted and ‘X’ drives the data port of the registers.
datae0
datae1
dataf0
dataf1
datab
dataa
datad
datac
2–35. The equation for this example is:
4-Input
4-Input
4-Input
4-Input
LUT
LUT
LUT
LUT
Figure
2–34, the carry-in signal feeds to adder0, and the
carry_out
carry_in
R = (X < Y) ? Y : X
adder0
adder1
D
D
reg0
reg1
Q
Q
To general or
To general or
To general or
local routing
To general or
local routing
local routing
local routing
© December 2009 Altera Corporation
Chapter 2: Arria GX Architecture
Adaptive Logic Modules