UPSD3234AV-24U1T STMicroelectronics, UPSD3234AV-24U1T Datasheet - Page 128
UPSD3234AV-24U1T
Manufacturer Part Number
UPSD3234AV-24U1T
Description
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer
STMicroelectronics
Datasheet
1.UPSD3234AV-24U1T.pdf
(170 pages)
- Current page: 128 of 170
- Download datasheet (3Mb)
www.DataSheet4U.com
uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV
POWER MANAGEMENT
All PSD Modules offer configurable power saving
options. These options may be used individually or
in combinations, as follows:
–
–
–
–
Figure 69. APD Unit
128/170
The primary and secondary Flash memory,
and SRAM blocks are built with power
management technology. In addition to using
special silicon design methodology, power
management technology puts the memories
into Standby Mode when address/data inputs
are not changing (zero DC current). As soon
as a transition occurs on an input, the affected
memory “wakes up,” changes and latches its
outputs, then goes back to standby. The
designer does not have to do anything special
to achieve Memory Standby Mode when no
inputs are changing—it happens
automatically.
The PLD sections can also achieve Standby
Mode when its inputs are not changing, as
described in the sections on the Power
Management Mode Registers (PMMR).
As with the Power Management Mode, the
Automatic Power Down (APD) block allows
the PSD Module to reduce to stand-by current
automatically. The APD Unit can also block
MCU address/data signals from reaching the
memories and PLDs.
Built in logic monitors the Address Strobe of
the MCU for activity. If there is no activity for a
certain time period (MCU is asleep), the APD
Unit initiates Power-down Mode (if enabled).
Once in Power-down Mode, all address/data
APD EN
PMMR0 BIT 1=1
ALE
RESET
CSI
CLKIN
DISABLE
FLASH/SRAM
TRANSITION
DETECTION
DETECT
EDGE
CLR
COUNTER
APD
PD
PD
–
–
signals are blocked from reaching memory
and PLDs, and the memories are deselected
internally. This allows the memory and PLDs
to remain in Standby Mode even if the
address/data signals are changing state
externally (noise, other devices on the MCU
bus, etc.). Keep in mind that any unblocked
PLD input signals that are changing states
keeps the PLD out of Stand-by Mode, but not
the memories.
PSD Chip Select Input (CSI, PD2) can be
used to disable the internal memories, placing
them in Standby Mode even if inputs are
changing. This feature does not block any
internal signals or disable the PLDs. This is a
good alternative to using the APD Unit. There
is a slight penalty in memory access time
when PSD Chip Select Input (CSI, PD2)
makes its initial transition from deselected to
selected.
The PMMRs can be written by the MCU at run-
time to manage power. The PSD Module
supports “blocking bits” in these registers that
are set to block designated signals from
reaching both PLDs. Current consumption of
the PLDs is directly related to the composite
frequency of the changes on their inputs (see
Figure
Significant power savings can be achieved by
blocking signals that are not used in DPLD or
CPLD logic equations.
DISABLE BUS
INTERFACE
72
and
PLD
Figure 73., page
CSIOP SELECT
FLASH SELECT
POWER DOWN
( PDN )
SRAM SELECT
SELECT
135).
AI06608
Related parts for UPSD3234AV-24U1T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 52 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 80 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 8BIT 256K FLASH 40MHZ 52TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC MCU 8032 64KB FLASH 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: