UPSD3234AV-24U1T STMicroelectronics, UPSD3234AV-24U1T Datasheet - Page 89
UPSD3234AV-24U1T
Manufacturer Part Number
UPSD3234AV-24U1T
Description
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer
STMicroelectronics
Datasheet
1.UPSD3234AV-24U1T.pdf
(170 pages)
- Current page: 89 of 170
- Download datasheet (3Mb)
www.DataSheet4U.com
Transceiver
USB Physical Layer Characteristics. The
lowing section describes the uPSD323X Devices
compliance to the Chapter 7 Electrical section of
the USB Specification, Revision 1.1. The section
contains all signaling, and physical layer specifica-
tions necessary to describe a low speed USB
function.
Low Speed Driver Characteristics. The
uPSD323X Devices use a differential output driver
to drive the Low Speed USB data signal onto the
USB cable. The output swings between the differ-
ential high and low state are well balanced to min-
imize signal skew. The slew rate control on the
driver minimizes the radiated noise and cross talk
on the USB cable. The driver’s outputs support
three-state operation to achieve bi-directional half
duplex operation. The uPSD323X Devices driver
Figure 44. Low Speed Driver Signal Waveforms
V
V
SE
SE
(max)
(min)
Signal Pins
V
SS
Driver
1.5 Mb/s
One Bit
Time
uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV
fol-
tolerates a voltage on the signal pins of -0.5V to
3.6V with respect to local ground reference without
damage. The driver tolerates this voltage for
10.0µs while the driver is active and driving, and
tolerates this condition indefinitely when the driver
is in its high impedance state.
A low speed USB connection is made through an
unshielded, untwisted wire cable a maximum of 3
meters in length. The rise and fall time of the sig-
nals on this cable are well controlled to reduce RFI
emissions while limiting delays, signaling skews
and distortions. The uPSD323X Devices driver
reaches the specified static signal levels with
smooth rise and fall times, resulting in segments
between low speed devices and the ports to which
they are connected.
Signal pins
pass output
spec levels
with minimal
reflections and
ringing
AI06629
89/170
Related parts for UPSD3234AV-24U1T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 52 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 80 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 8BIT 256K FLASH 40MHZ 52TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC MCU 8032 64KB FLASH 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: