UPSD3234AV-24U1T STMicroelectronics, UPSD3234AV-24U1T Datasheet - Page 132
UPSD3234AV-24U1T
Manufacturer Part Number
UPSD3234AV-24U1T
Description
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer
STMicroelectronics
Datasheet
1.UPSD3234AV-24U1T.pdf
(170 pages)
- Current page: 132 of 170
- Download datasheet (3Mb)
www.DataSheet4U.com
uPSD3234A, uPSD3234BV, uPSD3233B, uPSD3233BV
RESET TIMING AND DEVICE STATUS AT RESET
Upon Power-up, the PSD Module requires a Reset
(RESET) pulse of duration t
steady. During this period, the device loads inter-
nal configurations, clears some of the registers
and sets the Flash memory into operating mode.
After the rising edge of Reset (RESET), the PSD
Module remains in the Reset Mode for an addition-
al period, t
allowed.
The Flash memory is reset to the READ Mode
upon Power-up. Sector Select (FS0-FS7 and
CSBOOT0-CSBOOT3) must all be Low, WRITE
Strobe (WR, CNTL0) High, during Power-on
RESET for maximum security of the data contents
and to remove the possibility of a byte being writ-
ten on the first edge of WRITE Strobe (WR). Any
Flash memory WRITE cycle initiation is prevented
automatically when V
Warm RESET
Once the device is up and running, the PSD Mod-
ule can be reset with a pulse of a much shorter du-
ration, t
Figure 71. Reset (RESET) Timing
132/170
V
RESET
CC
NLNH
OPR
. The same t
, before the first memory access is
CC
Power-On Reset
V
is below V
t NLNH-PO
CC
(min)
OPR
NLNH-PO
period is needed
LKO
after V
.
t OPR
CC
is
before the device is operational after a Warm
RESET. Figure
up and Warm RESET.
I/O Pin, Register and PLD Status at RESET
Table
tus during Power-on RESET, Warm RESET, and
Power-down Mode. PLD outputs are always valid
during Warm RESET, and they are valid in Power-
on RESET once the internal Configuration bits are
loaded. This loading is completed typically long
before the V
the PLD is active, the state of the outputs are de-
termined by the PLD equations.
Reset of Flash Memory Erase and Program
Cycles
A Reset (RESET) also resets the internal Flash
memory state machine. During a Flash memory
Program or Erase cycle, Reset (RESET) termi-
nates the cycle and returns the Flash memory to
the READ Mode within a period of t
105
shows the I/O pin, register and PLD sta-
CC
ramps up to operating level. Once
71
shows the timing of the Power-
Warm Reset
t NLNH-A
t NLNH
NLNH-A
t OPR
AI02866b
.
Related parts for UPSD3234AV-24U1T
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 52 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC FLASH/MCU 64K 80 TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
MCU 8BIT 256K FLASH 40MHZ 52TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
IC MCU 8032 64KB FLASH 80TQFP
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
Flash Programmable System Devices with 8032 Microcontroller Core and 64Kbit SRAM
Manufacturer:
STMicroelectronics
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet: