TMPSNS-RTD1 Microchip Technology, TMPSNS-RTD1 Datasheet - Page 106

• Manufacturer Part Number: TMPSNS-RTD1
• Description: BOARD EVAL PT100 RTD TEMP SENSOR
• Manufacturer: Microchip Technology

Specifications of TMPSNS-RTD1

• Sensor Type: Temperature
• Interface: USB
• Embedded: Yes, MCU, 8-Bit
• Utilized Ic / Part: MCP3301, MCP6S26, PIC18F2550
• Processor To Be Evaluated: MCP6S26, MCP3301, MCP6024, MCP41010, PIC18F2550, TC1071, MCP6002
• Data Bus Width: 12 bit
• Interface Type: USB
• Lead Free Status / RoHS Status: Not applicable / Not applicable
• Voltage - Supply: -
• Sensitivity: -
• Sensing Range: -
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Not applicable / Not applicable

PIC18F2455/2550/4455/4550
9.3
The PIR registers contain the individual flag bits for the
peripheral interrupts. Due to the number of peripheral
interrupt sources, there are two Peripheral Interrupt
Request (Flag) registers (PIR1 and PIR2).
REGISTER 9-4:
DS39632E-page 104
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
Note 1:
SPPIF
R/W-0
PIR Registers
(1)
This bit is reserved on 28-pin devices; always maintain this bit clear.
SPPIF: Streaming Parallel Port Read/Write Interrupt Flag bit
1 = A read or a write operation has taken place (must be cleared in software)
0 = No read or write has occurred
ADIF: A/D Converter Interrupt Flag bit
1 = An A/D conversion completed (must be cleared in software)
0 = The A/D conversion is not complete
RCIF: EUSART Receive Interrupt Flag bit
1 = The EUSART receive buffer, RCREG, is full (cleared when RCREG is read)
0 = The EUSART receive buffer is empty
TXIF: EUSART Transmit Interrupt Flag bit
1 = The EUSART transmit buffer, TXREG, is empty (cleared when TXREG is written)
0 = The EUSART transmit buffer is full
SSPIF: Master Synchronous Serial Port Interrupt Flag bit
1 = The transmission/reception is complete (must be cleared in software)
0 = Waiting to transmit/receive
CCP1IF: CCP1 Interrupt Flag bit
Capture mode:
1 = A TMR1 register capture occurred (must be cleared in software)
0 = No TMR1 register capture occurred
Compare mode:
1 = A TMR1 register compare match occurred (must be cleared in software)
0 = No TMR1 register compare match occurred
PWM mode:
Unused in this mode.
TMR2IF: TMR2 to PR2 Match Interrupt Flag bit
1 = TMR2 to PR2 match occurred (must be cleared in software)
0 = No TMR2 to PR2 match occurred
TMR1IF: TMR1 Overflow Interrupt Flag bit
1 = TMR1 register overflowed (must be cleared in software)
0 = TMR1 register did not overflow
R/W-0
ADIF
PIR1: PERIPHERAL INTERRUPT REQUEST (FLAG) REGISTER 1
W = Writable bit
‘1’ = Bit is set
RCIF
R-0
TXIF
R-0
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
SSPIF
R/W-0
Note 1: Interrupt flag bits are set when an interrupt
2: User software should ensure the appropri-
condition occurs regardless of the state of
its corresponding enable bit or the Global
Interrupt Enable bit, GIE (INTCON<7>).
ate interrupt flag bits are cleared prior to
enabling an interrupt and after servicing
that interrupt.
(1)
CCP1IF
R/W-0
© 2009 Microchip Technology Inc.
x = Bit is unknown
TMR2IF
R/W-0
TMR1IF
R/W-0
bit 0