HD6417020SX20IV Renesas Electronics America, HD6417020SX20IV Datasheet - Page 367

• Manufacturer Part Number: HD6417020SX20IV
• Description: SH 1 CORE 32B MPU, 20MHZ/5V, 100
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7020r

Specifications of HD6417020SX20IV

• Core Processor: SH-1
• Core Size: 32-Bit
• Speed: 20MHz
• Connectivity: EBI/EMI, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

• Bit 2 (transmit-end interrupt enable (TEIE)): TEIE enables or disables the transmit-end
Bit 2: TEIE
0
1
• Bits 1 and 0 (clock enable 1 and 0 (CKE1 and CKE0)): CKE1 and CKE0 select the SCI clock
Bit 1:
CKE1
0
0
1
1
Notes: 1. The SCK pin is multiplexed with other functions. Set the pin function controller (PFC) to
RENESAS 350
interrupt (TEI) requested if TDR does not contain new transmit data when the MSB is
transmitted.
source and enable or disable clock output from the SCK pin. Depending on the combination of
CKE1 and CKE0, the SCK pin can be used for general-purpose input/output, serial clock
output, or serial clock input.
The CKE0 setting is valid only in the asynchronous mode, and only when the SCI is internally
clocked (CKE1 = 0). The CKE0 setting is ignored in the clocked synchronous mode, or when
an external clock source is selected (CKE1 = 1). Select the SCI operating mode in the serial
mode register (SMR) before setting CKE1 and CKE0. For further details on selection of the
SCI clock source, see table 13.9 in section 13.3, Operation.
Bit 0:
CKE0
0
1
0
1
2. Initial value
3. The output clock frequency is the same as the bit rate.
4. The input clock frequency is 16 times the bit rate.
select the SCK function and the SCK input/output of the SCK pin.
Description*
Synchronous mode
Clocked synchronous mode Internal clock, SCK pin used for serial clock output*
Synchronous mode
Clocked synchronous mode Internal clock, SCK pin used for serial clock output
Synchronous mode
Clocked synchronous mode External clock, SCK pin used for serial clock input
Synchronous mode
Clocked synchronous mode External clock, SCK pin used for serial clock input
Description
Transmit-end interrupt (TEI) requests are disabled* (initial value)
The TEI request can be cleared by reading the TDRE bit in the serial
status register (SSR) after it has been set to 1, then clearing TDRE to
0; by clearing the transmit end (TEND) bit to 0; or by clearing the TEIE
bit to 0.
Transmit-end interrupt (TEI) requests are enabled.
1
Internal clock, SCK pin used for input pin (input
signal is ignored or output pin output level is
undefined)
Internal clock, SCK pin used for clock output*
External clock, SCK pin used for clock input*
External clock, SCK pin used for clock input*
4
4
3
2