HD6417020SX20IV Renesas Electronics America, HD6417020SX20IV Datasheet - Page 409

• Manufacturer Part Number: HD6417020SX20IV
• Description: SH 1 CORE 32B MPU, 20MHZ/5V, 100
• Manufacturer: Renesas Electronics America
• Series: SuperH® SH7020r

Specifications of HD6417020SX20IV

• Core Processor: SH-1
• Core Size: 32-Bit
• Speed: 20MHz
• Connectivity: EBI/EMI, SCI
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Type: ROMless
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Program Memory Size: -
• Data Converters: -

3. After setting RDRF to 1, if the receive-data-full interrupt enable bit (RIE) is set to 1 in the
Transmitting and Receiving Serial Data Simultaneously (clocked synchronous mode): Figure
13.20 shows a sample flowchart for transmitting and receiving serial data simultaneously. The
procedure for transmitting and receiving serial data simultaneously is listed below.
1. SCI initialization: select the TxD and RxD pin function with the PFC.
2. SCI status check and transmit data write: read the serial status register (SSR), check that the
3. Receive error handling: if a receive error occurs, read the ORER bit in SSR to identify the
4. SCI status check and receive data read: read the serial status register (SSR), check that RDRF
5. To continue transmitting and receiving serial data: read the RDRF bit and RDR, and clear
RENESAS 392
RDR. If this check passes, the SCI sets RDRF to 1 and stores the received data in the RDR. If
the check does not pass (receive error), the SCI operates as indicated in table 13.8. When the
error flag is set to 1 and the RDRF bit is cleared to 0, the RDRF bit will not be set to 1 during
reception. When restarting the reception, make sure to clear the error flag to 0.
SCR, the SCI requests a receive-data-full interrupt (RXI). If the ORER bit is set to 1 and the
receive-data-full interrupt enable bit (RIE) in the SCR is also set to 1, the SCI requests a
receive-error interrupt (ERI).
TDRE bit is 1, then write transmit data in the transmit data register (TDR) and clear TDRE to
0. The TXI interrupt can also be used to determine if the TDRE bit has changed from 0 to 1.
error. After executing the necessary error handling, clear ORER to 0. Transmitting/receiving
cannot resume if ORER remains set to 1.
is set to 1, then read receive data from the receive data register (RDR) and clear RDRF to 0.
The RXI interrupt can also be used to determine if the RDRF bit has changed from 0 to 1.
RDRF to 0 before the frame MSB (bit 7) of the current frame is received. Also read the TDRE
bit to check whether it is safe to write (1); if so, write data in TDR, then clear TDRE to 0
before the MSB (bit 7) of the current frame is transmitted. When the DMAC is started by a
transmit-data-empty interrupt request (TXI) to write data in TDR, the TDRE bit is checked and
cleared automatically. When the DMAC is started by a receive-data-full interrupt (RXI) to read
RDR, the RDRF bit is cleared automatically.