MC56F8345VFGE Freescale Semiconductor, MC56F8345VFGE Datasheet - Page 34

• Manufacturer Part Number: MC56F8345VFGE
• Description: IC DSP 16BIT 60MHZ 128-LQFP
• Manufacturer: Freescale Semiconductor
• Series: 56F8xxxr

Specifications of MC56F8345VFGE

• Core Processor: 56800
• Core Size: 16-Bit
• Speed: 60MHz
• Connectivity: CAN, EBI/EMI, SCI, SPI
• Peripherals: POR, PWM, Temp Sensor, WDT
• Number Of I /o: 49
• Program Memory Size: 136KB (68K x 16)
• Program Memory Type: FLASH
• Ram Size: 6K x 16
• Voltage - Supply (vcc/vdd): 2.25 V ~ 3.6 V
• Data Converters: A/D 16x12b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 128-LQFP
• Data Bus Width: 16 bit
• Processor Series: MC56F83xx
• Core: 56800E
• Numeric And Arithmetic Format: Fixed-Point
• Device Million Instructions Per Second: 60 MIPs
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 49
• Data Ram Size: 8 KB
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Interface Type: SCI, SPI, CAN
• Minimum Operating Temperature: - 40 C
• For Use With: MC56F8367EVME - EVAL BOARD FOR MC56F83X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

34
(GPIOE10)
(GPIOE11)
(GPIOE12)
(GPIOE13)
(GPIOE8)
(GPIOE9)
CAN_TX
Signal
Name
IRQA
IRQB
TC0
TC1
TD0
TD1
TD2
TD3
Table 2-2 Signal and Package Information for the 128-Pin LQFP
Pin No.
120
111
113
107
108
109
110
52
53
Schmitt
Schmitt
Schmitt
Schmitt
Schmitt
Output
Output
Output
Output
Output
Input/
Input/
Input/
Input/
Open
Drain
Type
Input
56F8345 Technical Data, Rev. 17
enabled
enabled
enabled
During
Output
pull-up
pull-up
pull-up
Reset
Input,
Input,
Input,
State
Open
Drain
FlexCAN Transmit Data — CAN output with internal pull-up
enable at reset.*
* Note: If a pin is configured as open drain output mode, internal
pull-up will automatically be disabled when it outputs low.
Internal pull-up will be enabled unless it has been manually
disabled by clearing the corresponding bit in the PUREN register
of the GPIO module, when it outputs high.
If a pin is configured as push-pull output mode, internal pull-up
will automatically be disabled, whether it outputs low or high.
TC0 - 1 — Timer C, Channels 0 and 1
Port E GPIO — These GPIO pins can be individually
programmed as input or output pins.
At reset, these pins default to Timer functionality.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOE_PUR register. See
TD0 - TD3 — Timer D, Channels 0, 1, 2 and 3
Port E GPIO — These GPIO pins can be individually
programmed as input or output pins.
At reset, these pins default to Timer functionality.
To deactivate the internal pull-up resistor, clear the appropriate
bit of the GPIOE_PUR register. See
External Interrupt Request A and B — The IRQA and IRQB
inputs are asynchronous external interrupt requests during Stop
and Wait mode operation. During other operating modes, they
are synchronized external interrupt requests, which indicate an
external device is requesting service. They can be programmed
to be level-sensitive or negative-edge triggered.
To deactivate the internal pull-up resistor, set the IRQ bit in the
SIM_PUDR register. See
Signal Description
Part 6.5.6
for details.
Part 6.5.6
Part 6.5.6
Freescale Semiconductor
for details.
for details.
Preliminary