MC9S12NE64VTUE Freescale Semiconductor, MC9S12NE64VTUE Datasheet - Page 221

• Manufacturer Part Number: MC9S12NE64VTUE
• Description: IC MCU 64K FLASH EEPROM 80-TQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS12r

Specifications of MC9S12NE64VTUE

• Core Processor: HCS12
• Core Size: 16-Bit
• Speed: 25MHz
• Connectivity: EBI/EMI, Ethernet, I²C, SCI, SPI
• Peripherals: POR, PWM, WDT
• Number Of I /o: 38
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2.375 V ~ 3.465 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 80-TQFP Exposed Pad, 80-eTQFP, 80-HTQFP, 80-VQFP
• Processor Series: S12N
• Core: HCS12
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 125 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: - 0.3 V to + 3 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWHCS12
• Development Tools By Supplier: EVB9S12NE64E, DEMO9S12NE64E
• Minimum Operating Temperature: - 65 C
• On-chip Adc: 10 bit, 8 Channel
• Cpu Family: HCS12
• Device Core Size: 16b
• Frequency (max): 25MHz
• Total Internal Ram Size: 8KB
• # I/os (max): 70
• Number Of Timers - General Purpose: 4
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 2.625/3.465V
• Operating Supply Voltage (min): 2.357/2.375/3.135V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 80
• Package Type: TQFP
• For Use With: EVB9S12NE64E - BOARD EVAL FOR 9S12NE64DEMO9S12NE64E - DEMO BOARD FOR 9S12NE64
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

7.3.2.7
This read-only register contains the sequence complete flag, overrun flags for external trigger and FIFO
mode, and the conversion counter.
Read: Anytime
Write: Anytime (No effect on (CC2, CC1, CC0))
Freescale Semiconductor
CC[2:0]
Reset
ETORF
FIFOR
Field
SCF
2–0
7
5
4
W
R
SCF
Sequence Complete Flag — This flag is set upon completion of a conversion sequence. If conversion
sequences are continuously performed (SCAN = 1), the flag is set after each one is completed. This flag is
cleared when one of the following occurs:
0 Conversion sequence not completed
1 Conversion sequence has completed
External Trigger Overrun Flag — While in edge trigger mode (ETRIGLE = 0), if additional active edges are
detected while a conversion sequence is in process the overrun flag is set. This flag is cleared when one of the
following occurs:
0 No External trigger over run error has occurred
1 External trigger over run error has occurred
FIFO Over Run Flag — This bit indicates that a result register has been written to before its associated
conversion complete flag (CCF) has been cleared. This flag is most useful when using the FIFO mode because
the flag potentially indicates that result registers are out of sync with the input channels. However, it is also
practical for non-FIFO modes, and indicates that a result register has been over written before it has been read
(i.e., the old data has been lost). This flag is cleared when one of the following occurs:
0 No over run has occurred
1 An over run condition exists
Conversion Counter — These 3 read-only bits are the binary value of the conversion counter. The conversion
counter points to the result register that will receive the result of the current conversion. E.g. CC2 = 1, CC1 = 1,
CC0 = 0 indicates that the result of the current conversion will be in ATD result register 6. If in non-FIFO mode
(FIFO = 0) the conversion counter is initialized to zero at the begin and end of the conversion sequence. If in
FIFO mode (FIFO = 1) the register counter is not initialized. The conversion counters wraps around when its
maximum value is reached.
Aborting a conversion or starting a new conversion by write to an ATDCTL register (ATDCTL5-0) clears the
conversion counter even if FIFO=1.
ATD Status Register 0 (ATDSTAT0)
0
7
A) Write “1” to SCF
B) Write to ATDCTL5 (a new conversion sequence is started)
C) If AFFC=1 and read of a result register
A) Write “1” to ETORF
B) Write to ATDCTL2, ATDCTL3 or ATDCTL4 (a conversion sequence is aborted)
C) Write to ATDCTL5 (a new conversion sequence is started)
A) Write “1” to FIFOR
B) Start a new conversion sequence (write to ATDCTL5 or external trigger)
= Unimplemented or Reserved
0
0
6
Figure 7-9. ATD Status Register 0 (ATDSTAT0)
Table 7-17. ATDSTAT0 Field Descriptions
ETORF
MC9S12NE64 Data Sheet, Rev. 1.1
0
5
FIFOR
0
4
Description
0
0
3
CC2
0
2
Memory Map and Register Definition
CC1
0
1
CC0
0
0
221