ATSAM3S4CA-AU Atmel, ATSAM3S4CA-AU Datasheet - Page 308

• Manufacturer Part Number: ATSAM3S4CA-AU
• Description: IC MCU 32BIT 256KB FLASH 100LQFP
• Manufacturer: Atmel
• Series: SAM3Sr

Specifications of ATSAM3S4CA-AU

• Core Processor: ARM® Cortex-M3™
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: EBI/EMI, I²C, MMC, SPI, SSC, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, DMA, I²S, POR, PWM, WDT
• Number Of I /o: 79
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 48K x 8
• Voltage - Supply (vcc/vdd): 1.62 V ~ 1.95 V
• Data Converters: A/D 16x10/12b, D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: ATSAM3S
• No. Of I/o's: 79
• Ram Memory Size: 48KB
• Cpu Speed: 64MHz
• No. Of Timers: 6
• Rohs Compliant: Yes
• Processor Series: ATSAM3x
• Core: ARM Cortex M3
• 3rd Party Development Tools: JTRACE-CM3, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: ATSAM3S-EK
• Cpu Family: AT91
• Device Core: ARM Cortex-M3
• Device Core Size: 32b
• Frequency (max): 64MHz
• Total Internal Ram Size: 48KB
• # I/os (max): 79
• Number Of Timers - General Purpose: 6
• Operating Supply Voltage (typ): 1.8/3.3V
• Operating Supply Voltage (max): 1.95/3.6V
• Operating Supply Voltage (min): 1.62V
• On-chip Adc: 16-chx12-bit
• On-chip Dac: 2-chx12-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Table 19-1.
Notes:
308
Signal Name
VDDIO
VDDCORE
VDDPLL
GND
XIN
TST
PGMEN0
PGMEN1
PGMEN2
PGMNCMD
PGMRDY
PGMNOE
PGMNVALID
PGMM[3:0]
PGMD[15:0] or [7:0]
1. DATA[7:0] pertains to the SAM3SxA (48 bits).
2. PGMD[7:0] pertains to the SAM3SxA (48 bits).
SAM3S Preliminary
Signal Description List
(2)
Function
I/O Lines Power Supply
Core Power Supply
PLL Power Supply
Ground
Main Clock Input.
This input can be tied to GND. In this case, the
device is clocked by the internal RC oscillator.
Test Mode Select
Test Mode Select
Test Mode Select
Test Mode Select
Valid command available
0: Device is busy
1: Device is ready for a new command
Output Enable (active high)
0: DATA[15:0] or DATA[7:0]
1: DATA[15:0] or DATA[7:0]
Specifies DATA type (See
Bi-directional data bus
Table
(1)
(1)
is in input mode
is in output mode
19-2)
Clocks
Power
Test
PIO
Input/Output
Ground
Output
Output
Power
Power
Power
Type
Input
Input
Input
Input
Input
Input
Input
Input
Active
Level
High
High
High
High
Low
Low
Low
Low
Comments
32KHz to 50MHz
Must be connected to VDDIO
Must be connected to VDDIO
Must be connected to VDDIO
Must be connected to GND
Pulled-up input at reset
Pulled-up input at reset
Pulled-up input at reset
Pulled-up input at reset
Pulled-up input at reset
Pulled-up input at reset
6500C–ATARM–8-Feb-11