MCHC705JJ7CPE Freescale Semiconductor, MCHC705JJ7CPE Datasheet - Page 129

• Manufacturer Part Number: MCHC705JJ7CPE
• Description: IC MCU 8BIT 224 BYTES RAM 20PDIP
• Manufacturer: Freescale Semiconductor
• Series: HC05r

Specifications of MCHC705JJ7CPE

• Core Processor: HC05
• Core Size: 8-Bit
• Speed: 2.1MHz
• Connectivity: SIO
• Peripherals: POR, Temp Sensor, WDT
• Number Of I /o: 14
• Program Memory Size: 6KB (6K x 8)
• Program Memory Type: OTP
• Ram Size: 224 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 4x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-DIP (0.300", 7.62mm)
• Processor Series: HC705JJ
• Core: HC05
• Data Bus Width: 8 bit
• Data Ram Size: 224 B
• Interface Type: SIOP
• Maximum Clock Frequency: 2.1 MHz
• Number Of Programmable I/os: 14
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 4 Channel
• Package: 20PDIP
• Family Name: HC05
• Maximum Speed: 2.1 MHz
• Operating Supply Voltage: 3.3|5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

14.3.3 Jump/Branch Instructions
Jump instructions allow the CPU to interrupt the normal sequence of the program counter. The
unconditional jump instruction (JMP) and the jump-to-subroutine instruction (JSR) have no register
operand. Branch instructions allow the CPU to interrupt the normal sequence of the program counter
when a test condition is met. If the test condition is not met, the branch is not performed.
The BRCLR and BRSET instructions cause a branch based on the state of any readable bit in the first
256 memory locations. These 3-byte instructions use a combination of direct addressing and relative
addressing. The direct address of the byte to be tested is in the byte following the opcode. The third byte
is the signed offset byte. The CPU finds the effective branch destination by adding the third byte to the
program counter if the specified bit tests true. The bit to be tested and its condition (set or clear) is part of
the opcode. The span of branching is from –128 to +127 from the address of the next location after the
branch instruction. The CPU also transfers the tested bit to the carry/borrow bit of the condition code
register.
Freescale Semiconductor
MC68HC705JJ7 • MC68HC705JP7 Advance Information Data Sheet, Rev. 4.1
Branch if Carry Bit Clear
Branch if Carry Bit Set
Branch if Equal
Branch if Half-Carry Bit Clear
Branch if Half-Carry Bit Set
Branch if Higher
Branch if Higher or Same
Branch if IRQ/V
Branch if IRQ/V
Branch if Lower
Branch if Lower or Same
Branch if Interrupt Mask Clear
Branch if Minus
Branch if Interrupt Mask Set
Branch if Not Equal
Branch if Plus
Branch Always
Branch if Bit Clear
Branch Never
Branch if Bit Set
Branch to Subroutine
Unconditional Jump
Jump to Subroutine
Table 14-3. Jump and Branch Instructions
Instruction
PP
PP
Pin High
Pin Low
Mnemonic
BRCLR
BRSET
BHCC
BHCS
BMC
BMS
BRN
BCC
BCS
BEQ
BHS
BLO
BNE
BRA
BSR
JMP
BLS
BPL
JSR
BMI
BHI
BIH
BIL
Instruction Types
129