EP4CE55F23C8N Altera, EP4CE55F23C8N Datasheet - Page 220

• Manufacturer Part Number: EP4CE55F23C8N
• Description: IC CYCLONE IV FPGA 55K 484FBGA
• Manufacturer: Altera
• Series: CYCLONE® IV Er

Specifications of EP4CE55F23C8N

• Number Of Logic Elements/cells: 55856
• Number Of Labs/clbs: 3491
• Total Ram Bits: 2340000
• Number Of I /o: 324
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 484-FBGA
• Family Name: Cyclone IV
• Number Of Logic Blocks/elements: 55856
• # I/os (max): 324
• Logic Cells: 55856
• Ram Bits: 2396160
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 484
• Package Type: FBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Compliant

8–54
Cyclone IV Device Handbook, Volume 1
Programming Serial Configuration Devices In-System with the JTAG Interface
Cyclone IV devices in a single- or multiple-device chain support in-system
programming of a serial configuration device with the JTAG interface through the SFL
design. The intelligent host or download cable of the board can use the four JTAG pins
on the Cyclone IV device to program the serial configuration device in system, even if
the host or download cable cannot access the configuration pins (DCLK, DATA, ASDI,
and nCS pins).
The SFL design is a JTAG-based in-system programming solution for Altera serial
configuration devices. The SFL is a bridge design for the Cyclone IV device that uses
their JTAG interface to access the EPCS JTAG Indirect Configuration Device
Programming (.jic) file and then uses the AS interface to program the EPCS device.
Both the JTAG interface and AS interface are bridged together inside the SFL design.
In a multiple device chain, you must only configure the master device that controls
the serial configuration device. Slave devices in the multiple device chain that are
configured by the serial configuration device do not have to be configured when
using this feature. To successfully use this feature, set the MSEL pins of the master
device to select the AS configuration scheme
page
programming through the Cyclone IV device JTAG interface has three stages, which
are described in the following sections:
■
■
■
Loading the SFL Design
The SFL design is a design inside the Cyclone IV device that bridges the JTAG
interface and AS interface with glue logic.
The intelligent host uses the JTAG interface to configure the master device with a SFL
design. The SFL design allows the master device to control the access of four serial
configuration device pins, also known as the Active Serial Memory Interface (ASMI)
pins, through the JTAG interface. The ASMI pins are serial clock input (DCLK), serial
data output (DATA), AS data input (ASDI), and active-low chip select (nCS) pins.
If you configure a master device with an SFL design, the master device enters user
mode even though the slave devices in the multiple device chain are not being
configured. The master device enters user mode with a SFL design even though the
CONF_DONE signal is externally held low by the other slave devices in chain.
Figure 8–29
design.
“Loading the SFL Design”
“ISP of the Configuration Device” on page 8–55
“Reconfiguration” on page 8–56
8–8, and
shows the JTAG configuration of a single Cyclone IV device with a SFL
Table 8–5 on page
Chapter 8: Configuration and Remote System Upgrades in Cyclone IV Devices
8–9). The serial configuration device in-system
(Table 8–3 on page
© December 2010 Altera Corporation
8–8,
Table 8–4 on
Configuration