LPC4350FET256,551 NXP Semiconductors, LPC4350FET256,551 Datasheet - Page 75

• Manufacturer Part Number: LPC4350FET256,551
• Description: IC MCU 32BIT 256LBGA
• Manufacturer: NXP Semiconductors
• Series: LPC43xxr

Specifications of LPC4350FET256,551

• Core Processor: ARM® Cortex™-M4/M0
• Core Size: 32-Bit Dual-Core
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 146
• Program Memory Size: -
• Program Memory Type: ROMless
• Eeprom Size: -
• Ram Size: 264K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

NXP Semiconductors
LPC4350_30_20_10
Objective data sheet
7.17.2.1 Features
7.17.2 SPI Flash Interface (SPIFI)
7.17.3 SD/MMC card interface
7.17.4 External Memory Controller (EMC)
The SPI Flash Interface allows low-cost serial flash memories to be connected to the ARM
Cortex-M4 processor with little performance penalty compared to parallel flash devices
with higher pin count.
After a few commands configure the interface at startup, the entire flash content is
accessible as normal memory using byte, halfword, and word accesses by the processor
and/or DMA channels. Erasure and programming are handled by simple sequences of
commands.
Many serial flash devices use a half-duplex command-driven SPI protocol for device setup
and initialization and then move to a half-duplex, command-driven 4-bit protocol for
normal operation. Different serial flash vendors and devices accept or require different
commands and command formats. SPIFI provides sufficient flexibility to be compatible
with common flash devices and includes extensions to help insure compatibility with future
devices.
The SD/MMC card interface supports the following modes to control:
The LPC4350/30/20/10 EMC is a Memory Controller peripheral offering support for
asynchronous static memory devices such as RAM, ROM, and flash. In addition, it can be
used as an interface with off-chip memory-mapped devices and peripherals.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Internal four-word FIFO per channel.
Supports 8, 16, and 32-bit wide transactions.
Big-endian and little-endian support. The DMA Controller defaults to little-endian
mode on reset.
An interrupt to the processor can be generated on a DMA completion or when a DMA
error has occurred.
Raw interrupt status. The DMA error and DMA count raw interrupt status can be read
prior to masking.
Interfaces to serial flash memory in the main memory map.
Supports classic and 4-bit bidirectional serial protocols.
Half-duplex protocol compatible with various vendors and devices.
Data rates of up to 40 MB per second.
Supports DMA access.
Secure Digital memory (SD version 3.0)
Secure Digital I/O (SDIO version 2.0)
Consumer Electronics Advanced Transport Architecture (CE-ATA version 1.1)
MultiMedia Cards (MMC version 4.4)
All information provided in this document is subject to legal disclaimers.
Rev. 2.1 — 23 September 2011
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
© NXP B.V. 2011. All rights reserved.
75 of 145