LPC4350FET256,551 NXP Semiconductors, LPC4350FET256,551 Datasheet - Page 85

• Manufacturer Part Number: LPC4350FET256,551
• Description: IC MCU 32BIT 256LBGA
• Manufacturer: NXP Semiconductors
• Series: LPC43xxr

Specifications of LPC4350FET256,551

• Core Processor: ARM® Cortex™-M4/M0
• Core Size: 32-Bit Dual-Core
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 146
• Program Memory Size: -
• Program Memory Type: ROMless
• Eeprom Size: -
• Ram Size: 264K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

NXP Semiconductors
LPC4350_30_20_10
Objective data sheet
7.21.1.1 Features
7.21.1 RTC
7.21.2 Alarm timer
7.22.1 Configuration registers (CREG)
7.22.2 System Control Unit (SCU)
7.21 Peripherals in the RTC power domain
7.22 System control
The Real Time Clock (RTC) is a set of counters for measuring time when system power is
on, and optionally when it is off. It uses very little power when its registers are not being
accessed by the CPU, especially reduced power modes. The RTC is clocked by a
separate 32 kHz oscillator that produces a 1 Hz internal time reference. The RTC is
powered by its own power supply pin, VBAT.
The alarm timer is a 16-bit timer and counts down at 1 kHz from a preset value generating
alarms in intervals of up to 1 min. The counter triggers a status bit when it reaches 0x00
and asserts an interrupt if enabled.
The alarm timer is part of the RTC power domain and can be battery powered.
The following settings are controlled in the configuration register block:
In addition, the CREG block contains the part identification and part configuration
information.
The system control unit determines the function and electrical mode of the digital pins and
allows switching between analog and digital modes of pads that are capable of both
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Measures the passage of time to maintain a calendar and clock. Provides seconds,
minutes, hours, day of month, month, year, day of week, and day of year.
Ultra-low power design to support battery powered systems. Less than <tbd> required
for battery operation. Uses power from the CPU power supply when it is present.
Dedicated battery power supply pin.
RTC power supply is isolated from the rest of the chip.
Calibration counter allows adjustment to better than 1 sec/day with 1 sec resolution.
Periodic interrupts can be generated from increments of any field of the time registers.
Alarm interrupt can be generated for a specific date/time.
BOD trip settings
Oscillator output
DMA-to-peripheral muxing
Ethernet mode
Memory mapping
Timer/USART inputs
Enabling the USB controllers
All information provided in this document is subject to legal disclaimers.
Rev. 2.1 — 23 September 2011
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
© NXP B.V. 2011. All rights reserved.
85 of 145