LPC4350FET256,551 NXP Semiconductors, LPC4350FET256,551 Datasheet - Page 76

• Manufacturer Part Number: LPC4350FET256,551
• Description: IC MCU 32BIT 256LBGA
• Manufacturer: NXP Semiconductors
• Series: LPC43xxr

Specifications of LPC4350FET256,551

• Core Processor: ARM® Cortex™-M4/M0
• Core Size: 32-Bit Dual-Core
• Speed: 150MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, Microwire, SD/MMC, SPI, SSI, SSP, UART/USART, USB OTG
• Peripherals: Brown-out Detect/Reset, DMA, I²S, LCD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 146
• Program Memory Size: -
• Program Memory Type: ROMless
• Eeprom Size: -
• Ram Size: 264K x 8
• Voltage - Supply (vcc/vdd): 2.2 V ~ 3.6 V
• Data Converters: A/D 16x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-LBGA
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

NXP Semiconductors
LPC4350_30_20_10
Objective data sheet
7.17.4.1 Features
7.17.5.1 Features
7.17.5 High-speed USB Host/Device/OTG interface (USB0)
Note: Synchronous static memory devices (synchronous burst mode) are not supported.
Remark: The USB0 controller is available on parts LPC4350/30/20. See
The USB OTG module allows the LPC4350/30/20/10 to connect directly to a USB Host
such as a PC (in device mode) or to a USB Device in host mode.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Dynamic memory interface support including single data rate SDRAM.
Asynchronous static memory device support including RAM, ROM, and flash, with or
without asynchronous page mode.
Low transaction latency.
Read and write buffers to reduce latency and to improve performance.
8/16/32 data and 24 address lines wide static memory support.
16 bit and 32 bit wide chip select SDRAM memory support.
Static memory features include:
– Asynchronous page mode read
– Programmable Wait States
– Bus turnaround delay
– Output enable and write enable delays
– Extended wait
Four chip selects for synchronous memory and four chip selects for static memory
devices.
Power-saving modes dynamically control EMC_CKEOUT and EMC_CLK signals to
SDRAMs.
Dynamic memory self-refresh mode controlled by software.
Controller supports 2048 (A0 to A10), 4096 (A0 to A11), and 8192 (A0 to A12) row
address synchronous memory parts. That is typical 512 MB, 256 MB, and 128 MB
parts, with 4, 8, 16, or 32 data bits per device.
Separate reset domains allow the for auto-refresh through a chip reset if desired.
Complies with Universal Serial Bus specification 2.0.
Complies with USB On-The-Go supplement.
Complies with Enhanced Host Controller Interface Specification.
Supports auto USB 2.0 mode discovery.
Supports all high-speed USB-compliant peripherals.
Supports all full-speed USB-compliant peripherals.
Supports software Host Negotiation Protocol (HNP) and Session Request Protocol
(SRP) for OTG peripherals.
Contains UTMI+ compliant transceiver (PHY).
Supports interrupts.
All information provided in this document is subject to legal disclaimers.
Rev. 2.1 — 23 September 2011
32-bit ARM Cortex-M4/M0 microcontroller
LPC4350/30/20/10
© NXP B.V. 2011. All rights reserved.
Table
2.
76 of 145